* Disable RESET keycode because of naming conflicts
* Add Pico SDK as submodule
* Add RP2040 build support to QMK
* Adjust USB endpoint structs for RP2040
* Add RP2040 bootloader and double-tap reset routine
* Add generic and pro micro RP2040 boards
* Add RP2040 onekey keyboard
* Add WS2812 PIO DMA enabled driver and documentation
Supports regular and open-drain output configuration. RP2040 GPIOs are
sadly not 5V tolerant, so this is a bit use-less or needs extra hardware
or you take the risk to fry your hardware.
* Adjust SIO Driver for RP2040
* Adjust I2C Driver for RP2040
* Adjust SPI Driver for RP2040
* Add PIO serial driver and documentation
* Add general RP2040 documentation
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Initial import of wear-leveling algorithm.
* Alignment.
* Docs tweaks.
* Lock/unlock.
* Update quantum/wear_leveling/wear_leveling_internal.h
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* More tests, fix issue with consolidation when unlocked.
* More tests.
* Review comments.
* Add plumbing for FNV1a.
* Another test checking that checksum mismatch clears the cache.
* Check that the write log still gets played back.
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Refactor steno into STENO_ENABLE_[ALL|GEMINI|BOLT]
* Update stenography documentation
* STENO_ENABLE_TXBOLT → STENO_ENABLE_BOLT
TXBOLT is a better name but BOLT is more consistent with the
pre-existing TX Bolt related constants, which all drop the "TX " prefix
* Comments
* STENO_ENABLE_[GEMINI|BOLT|ALL] → STENO_PROTOCOL = [geminipr|txbolt|all]
* Add note on lacking V-USB support
* Clear chord at the end of the switch(mode){send_steno_chord} block
* Return true if NOEVENT
* update_chord_xxx → add_xxx_key_to_chord
* Enable the defines for all the protocols if STENO_PROTOCOL = all
* Mention how to use `steno_set_mode`
* Set the default steno protocol to "all"
This is done so that existing keymaps invoking `steno_set_mode` don't
all suddenly break
* Add data driver equivalents for stenography feature
* Document format of serial steno packets
(Thanks dnaq)
* Add missing comma
* Fix RGB heatmap to use XY positions
* lower effect area limit and make configurable
* tidy up macro
* Fix triggering in both directions.
* add docs
* fix bug when decreasing value
* performance tweak
* Move SPLIT_HAND_PIN setup to split_pre_init
* doppelganger should use old behaviour
* Add comment for future
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Fix Caps Word and Unicode Map
* Tests for Caps Word + Auto Shift and Unicode Map.
* Fix formatting
* Add additional keyboard report expectation macros
This commit defines five test utilities, EXPECT_REPORT, EXPECT_UNICODE,
EXPECT_EMPTY_REPORT, EXPECT_ANY_REPORT and EXPECT_NO_REPORT for use with
TestDriver.
EXPECT_REPORT sets a gmock expectation that a given keyboard report will
be sent. For instance,
EXPECT_REPORT(driver, (KC_LSFT, KC_A));
is shorthand for
EXPECT_CALL(driver,
send_keyboard_mock(KeyboardReport(KC_LSFT, KC_A)));
EXPECT_UNICODE sets a gmock expectation that a given Unicode code point
will be sent using UC_LNX input mode. For instance for U+2013,
EXPECT_UNICODE(driver, 0x2013);
expects the sequence of keys:
"Ctrl+Shift+U, 2, 0, 1, 3, space".
EXPECT_EMPTY_REPORT sets a gmock expectation that a given keyboard
report will be sent. For instance
EXPECT_EMPTY_REPORT(driver);
expects a single report without keypresses or modifiers.
EXPECT_ANY_REPORT sets a gmock expectation that a arbitrary keyboard
report will be sent, without matching its contents. For instance
EXPECT_ANY_REPORT(driver).Times(1);
expects a single arbitrary keyboard report will be sent.
EXPECT_NO_REPORT sets a gmock expectation that no keyboard report will
be sent at all.
* Add tap_key() and tap_keys() to TestFixture.
This commit adds a `tap_key(key)` method to TestFixture that taps a
given KeymapKey, optionally with a specified delay between press and
release.
Similarly, the method `tap_keys(key_a, key_b, key_c)` taps a sequence of
KeymapKeys.
* Use EXPECT_REPORT, tap_keys, etc. in most tests.
This commit uses EXPECT_REPORT, EXPECT_UNICODE, EXPECT_EMPTY_REPORT,
EXPECT_NO_REPORT, tap_key() and tap_keys() test utilities from the
previous two commits in most tests. Particularly the EXPECT_REPORT
macro is frequently useful and makes a nice reduction in boilerplate
needed to express many tests.
Co-authored-by: David Kosorin <david@kosorin.net>
This is a minor bug fix for Caps Word. Currently, Caps Word turns off
whenever a non-shift mod becomes active. This is done to avoid
interfering with hotkeys.
This commit makes an exception to continue Caps Word when AltGr (right
Alt) is held. Outside the US, the AltGr key is used to type additional
symbols (https://en.wikipedia.org/wiki/AltGr_key). Depending on the
language, these may include symbols used within words like accented
letters where it would be desirable to continue Caps Word.
* Fix state updates of one-shot locked modifiers
Activating additional one-shot locked modifiers removed previously enabled locked modifiers from the state.
`get_oneshot_locked_mods` returned zero when two or more one-shot locked modifiers were enabled and then one was disabled.
* Do not delete one-shot locked modifiers on a one-shot layer toggle
Non-locked one-shot modifiers are not removed so this behavior adds inconsistency.
Also the one-shot locked modifiers state was reset without unregistering any modifiers.
* Add GET_TAPPING_TERM macro to reduce duplicate code
The macro gives the right tapping term depending on whether per-key
tapping terms and/or dynamic tapping terms are enabled. Unnecessary
function calls and variable resolution are avoided.
Fixes#16472.
* Use GET_TAPPING_TERM for Cirque trackpads
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Install dependencies before executing unit tests.
* Split out UTF-8 decoder.
* Fixup python formatting rules.
* Add documentation for QGF/QFF and the RLE format used.
* Add CLI commands for converting images and fonts.
* Add stub rules.mk for QP.
* Add stream type.
* Add base driver and comms interfaces.
* Add support for SPI, SPI+D/C comms drivers.
* Include <qp.h> when enabled.
* Add base support for SPI+D/C+RST panels, as well as concrete implementation of ST7789.
* Add support for GC9A01.
* Add support for ILI9341.
* Add support for ILI9163.
* Add support for SSD1351.
* Implement qp_setpixel, including pixdata buffer management.
* Implement qp_line.
* Implement qp_rect.
* Implement qp_circle.
* Implement qp_ellipse.
* Implement palette interpolation.
* Allow for streams to work with either flash or RAM.
* Image loading.
* Font loading.
* QGF palette loading.
* Progressive decoder of pixel data supporting Raw+RLE, 1-,2-,4-,8-bpp monochrome and palette-based images.
* Image drawing.
* Animations.
* Font rendering.
* Check against 256 colours, dump out the loaded palette if debugging enabled.
* Fix build.
* AVR is not the intended audience.
* `qmk format-c`
* Generation fix.
* First batch of docs.
* More docs and examples.
* Review comments.
* Public API documentation.
Fixes compilation issues when bluetooth is enabled, due to issues
with cpp used by bluetooth code.
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
After executing `setPinInputHigh(pin)`, it is necessary to wait for the charging time to read from the corresponding pin. This is the same as requiring `matrix_output_unselect_delay()` after doing `unselect_row()` in matrix.c.
* Don't make EEPROM size assumptions with dynamic keymaps.
* Add support for checking against emulated flash, error out if someone attempts to build a board without specifying EEPROM size.
* Reorder defines so that MCU is considered last.
* Refactor EEPROM definitions for simplicity.
* Fix max sizing of kabedon/kabedon980.
* Fix max sizing of mechlovin/olly/jf.
* Fix unit tests.
* Review comments, add messages with values during build failures.
* Diff reduction between ADNS9800 and PMW3360 drivers.
They are very similar devices. This (somewhat) unreadable diff is
essentially a no-op, but it makes a `vimdiff` between the 2 drivers much
more readable.
* Cleanup pwm3360 driver some more.
Remove redundant calls to spi_start() and spi_stop(), as pmw3360_write()
will already call these.
* Draft implementation
* formatting
* fix combined buttons
* remove pimoroni throttle
* sync pointing on a throttle loop with checksum
* no longer used
* doh
Co-authored-by: Drashna Jaelre <drashna@live.com>
* switch pimoroni to a cpi equivalent
* add cpi support
* allow user modification of seperate mouse reports
* a little tidy up
* add *_RIGHT defines.
* docs
* doxygen comments
* basic changelog
* clean up pimoroni
* small doc fixes
* Update docs/feature_pointing_device.md
Co-authored-by: Drashna Jaelre <drashna@live.com>
* performance tweak if side has usb
* Don't run init funtions on wrong side
* renamed some variables for consistency
* fix pimoroni typos
* Clamp instead of OR
* Promote combined values to uint16_t
* Update pointing_device.c
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Migrate Thermal Printer feature to UART driver
* Migrate 40percentclub UT47 to UART driver
* Migrate Centromere to UART driver
* Migrate Chimera Ergo to UART driver
* Migrate Chimera Let's Split to UART driver
* Migrate Chimera Ortho to UART driver
* Migrate Chimera Ortho Plus to UART driver
* Migrate Comet46 to UART driver
* Migrate Palm USB converter to UART driver
* Migrate Sun USB converter to UART driver
* Migrate Dichotomy to UART driver
* Migrate Honeycomb to UART driver
* Migrate Mitosis to UART driver
* Migrate Redox W to UART driver
* Migrate Uni660 to UART driver
* Migrate Telophase to UART driver
* New feature: `DYNAMIC_TAPPING_TERM_ENABLE`
3 new quantum keys to configure the tapping term on the fly.
* Replace sprintf call in tapping_term_report by get_u16_str
* Replace tab with 4 spaces
* macros in json keymaps
* add advanced macro support to json
* add a note about escaping macro strings
* add simple examples
* format json
* add support for language specific keymap extras
* switch to dictionaries instead of inline text for macros
* use SS_TAP on the innermost tap keycode
* add the new macro format to the schema
* document the macro limit
* add the json keyword for syntax highlighting
* fix format that vscode screwed up
* Update feature_macros.md
* add tests for macros
* change ding to beep
* add json support for SENDSTRING_BELL
* update doc based on feedback from sigprof
* document host_layout
* remove unused var
* improve carriage return handling
* support tab characters as well
* Update docs/feature_macros.md
Co-authored-by: Nick Brassel <nick@tzarc.org>
* escape backslash characters
* format
* flake8
* Update quantum/quantum_keycodes.h
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Made static backlight pwm resolution configurable
* Made breathing backlighting configurable too
* Finished my ifdef
* Ran clang-format
* Added missing semi-colon
* Solved weird behaviour by right-shifting the right amount
* Made breathing period scaled on actual pwm frequency
* Made the low end deadzone scaled on the top value
* Moved 'pwm_frequency' declaration outside ifdef
* Fixed 'never used' error
* Fixed 'never used' error
* Fixed breathing ISR to 120Hz
* Removed pwm_frequency constant
Constant is no longer needed since running the breathing ISR at a fixed 120Hz
* Re-add brightness limiting
* re-introduce scaling
* Reimplements WPM feature.
- Now calculates exact WPM over the last up to three seconds of typing.
- WPM_SMOOTHING removed, as it's no longer needed.
- WPM_SAMPLE_SECONDS added, to specify how long a period to average WPM
over, set to 5 seconds by default.
- WPM_SAMPLE_PERIODS added, to specify how many sampling buffers we'll
use. Each one uses one extra byte of space. Having more will lead
to smoother decay of WPM values. Defaults to 50 (we're saving so
many bytes of firmware space I felt like being extravagent, and this
change is still a big size saving overall)
- WPM_UNFILTERED option added (defaults to unset), which disables all
filtering within the WPM feature. This saves some space in the
firmware and also reduces latency between typing and the WPM
calculation measuring it. (saves 70 bytes in my tests)
- WPM_LAUNCH_CONTROL added (defaults to unset). When typing begins
while the current displayed WPM value is zero, the WPM calculation
only considers the time elapsed since typing began, not the whole
WPM_SAMPLE_SECONDS buffer. The result of this is that the displayed
WPM value much more rapidly reaches an accurate WPM value, even when
results are being filtered. (costs 22 bytes in my tests)
- Updates documentation to reflect changed options.
Saves about 900 bytes, in my tests, compared against the previous implementation,
with default settings.
* Apply suggestions from code review
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
Co-authored-by: Trevor Powell <trevor@vectorstorm.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
This also add support for specifying a LED pin to indicate haptic status,
and also adds support for a haptic-enable pin, which is useful to turn off
the boost converter on the solenoid driver.
* Gets RGB working on a split keyboard with IS31FL3733. Currently needs small tweak to re-enable WS2812
* Added helper function
* Trying to integrate the function
* Moved functionality into a macro
* Swapped conditional for a macro everywhere
* Tidying up
* More code cleanup
* Documentation updates
* Fixed formatting via linter
* Switching to a function from a macro
* Fixed compile error
* Fixing WS2812 behavior. UNTESTED.
* Updated documentation about the driver addresses.
* Fixed code for WS2812
* Trying to add in LED_MATRIX support
* Updated effects for LED matrix
* Updated third-party effect defines.
* Ran format-c on modified files
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
* Move to static inline. Avoids issues with gcc v8+
* Move helper function for LED_matrix to static inline to avoid issues with gcc v8+
Co-authored-by: Vlad Kvitnevskiy <vladkvit@outlook.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add support for RISC-V builds and GD32VF103 MCU
* Add toolchain selection in chibios.mk based on the mcu selected in
mcu_selection.mk
* Reorder and added comments to chibios.mk to have a streamlined makefile
* Add GD32VF103 mcu to possible targets for QMK.
* Add STM32 compatibility for GD32VF103 MCU, this is hacky but more efficent
then rewriting every driver.
* Add GigaDevice DFU bootloader as flash target, please note that
dfu-util of at least version 0.10 is needed.
* Add analog driver compatibility
* Add apa102 bitbang driver compatibility
* Add ws2812 bitbang driver compatibility
* Add eeprom in flash emulation compatibility
* Allow faster re-builds with ccache
* Add SiPeed Longan Nano to platform files
* Add SiPeed Longan Nano Onekeys
* Make quine compatible with other bootloaders
* Support builds with picolibc
* Add risc-v toolchain to arch and debian/ubuntu scripts
* Remove SERIAL_LINK
* more stale paths in doxygen-todo
* Fix
* More refs
* Update testing docs
* Update doxygen-todo
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Move Audio drivers from quantum to platform drivers folder
* fix path for audio drivers
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add power tracking API to lufa and chibios targets
* power.c: Pass through power state to the notify function
* power: added notify_power_state_change_user too.
* making it pass the PR linter
* Add a POWER_STATE_NO_INIT state, that we start in before calling power_init();
* Rename *power* to *usb_power*
* removing stray newline
* Rename usb_power* to usb_device_state*
* Update quantum/usb_device_state.h
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Fix comment
* usb_device_state.h: Don't include quantum.h, only the necessary headers.
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Use memcmp and memcpy to compare and copy slave matrix.
...and memset to initialize `matrix` and `raw_matrix`.
Increased my scan rate (while connected) by ~100 (on Ergodox Infinity).
Effect on AVR is unknown.
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Fix `matrix_post_scan` signalling change on every scan while disconnected.
* Undo removal of initialization of `slave_matrix`.
This has the effect of increasing my Ergodox Infinity firmware size by 8
bytes instead of decreasing by 8 bytes, and lowers the scan rate while
connected back to the initial value before these changes, but _might_
solve some issues on AVR.
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
Without this build would fail, if a keyboard had haptic feedback enabled,
TAPPING_TOGGLE was not overridden in a config.h, and if NO_HAPTIC_MOD was
defined in config.h.
* Revert "Short term bodge for firmware size bloat (#14144)"
This reverts commit a8d6547346.
* Revert "Tidy up quantum.c now some of tmk_core has been merged (#14083)"
This reverts commit c4dbf4bf01.
* adding uf2 flash support for blackpill 401
* forgot to add blackpill to keyboard header file
* making changes requested by drashna
* fixing tzarc s comments
* removing the keyboard
* undo the change to dactyl_manuform.h
* Make solo half of split keyboards (more) usable.
Using only one half of a split keyboard (that's using the split_common
framework to communicate) is not a great experience, since several read
timeouts per scan cycle cause an unusably slow scan rate.
This change blocks all split communication attempts for 500 ms
(configurable) after an error occurs, causing the scan rate to become at
least _more_ usable, but might need some tweaking to work fully on most
keyboards. One read timeout still needs to occur after the 500 ms has
passed, and if that timeout isn't low enough, some scan cycles may still
be too slow.
* Fix lint complaint.
* Require 25 consecutive comm errors to see comms as disconnected.
The number of max errors can be overridden by defining
`SPLIT_MAX_CONNECTION_ERRORS`.
* Add comments to new defines, and ability to disable disconnection check.
Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible
by most relevant numbers for the description.
* Make lint happy ...again
* Only update `connection_check_timer` when needed.
* Add new defines to split keyboard documentation.
* Move connection timeout logic to transport.c, add `is_transport_connected`.
* Use split_common disconnection logic in matrix.c.
Instead of doing more or less the same thing twice.
* Move disconnection logic to `transport_master`.
Is a cleaner implementation, and causes the scan rate while disconnected
to increase instead of decrease.
* Lint fixes.
* Lower default `SERIAL_USART_TIMEOUT` to 20 ms.
The read timeout must be low enough to not cause exessively long scan
cycles when using a solo split half. 10 ms was determined from testing
to work fine even with the slowest defined baudrate of 19200 (5 ms was
too low for that case), so 20 ms should be fine for most cases.
* Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h
Was somewhat mistakenly included in an earlier PR.
* Fix building with `USE_I2C`.
* Reduce built firmware size.
Not really sure why this works, the idea was taken from tzarc's work on
split disconnection.
* Tweak and improve opt-out for split disconnection logic.
There are now two ways to opt out from this feature:
* Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable
the connection status checks (also affects the slave matrix reset logic in
matrix.c, though).
* Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the
communication throttling while disconnected. Will make the firmware
smaller.
* Make split disconnection logic work with custom transports.
Includes a fallback implementation for keyboards using a custom
split_util.c but not a custom matrix.c (currently no such keyboard seems
to be merged, though).
* Remove unnecessary include of timer.h
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Remove hysteresis on 4x encoders
Sometimes, controller skips encoder pulses and when it returns to default position, the encoder_pulses variable isn't equals 0. And when I turn encoder in opposite direciton, it skips first click becase of encoder_pulses crosses zero. To prevent this, I add the ENCODER_DEFAULT_POS constant, and reset encoder_pulses into 0 when the state variable equals ENCODER_DEFAULT_POS.
* Documentation for ENCODER_DEFAULT_POS
* Add digitizer HID interface for setting the mouse cursor position at
absolute screen coordinates. Tested on Pro Micro, Proton C and
Blackpill.
* Update docs/feature_digitizer.md
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add missing copyrights
Add V-USB support
* Add support for digitizer dedicated endpoint for lufa and chibios.
Fix formatting issues
Move digitizer_task definition to the feature's base implementation file
* Run cformat on modified files
* Change digitizer report usage to Digitizer instead of Pen to avoid
pointer disappearing on Windows.
* Update tmk_core/protocol/vusb/vusb.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Run cformat from docker image
* Remove send_digitizer from host_driver_t and instead rely on the
declaration being the interface to the implementation in each
HW-specific usb implementation.
* Fix build : send_digitizer shouldn't be static in vusb and add
weak-linkage implementation for tests without usb implementation
* Change digitizer user interface to match pointing device's
* Update documentation with new API
Co-authored-by: a-chol <nothing@none.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Change animations to require explicet activation
* Add support for legacy config
* Make default for now
* Add LED Matrix support
* change LED Matrix docs
* Enable sync of OLED/ST7565 display on/off state on Splits
* Only send if states are not matched
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
- Dump key buffer when combos are disabled.
- Recursive calls to `dump_key_buffer` need to start dumping the buffer
from index i+1 to avoid possible infinite loops.
- Handle combo key releases even though combo processing is disabled.
* quantum/command.c: coalesce `print()`s in `command_common_help()` & `print_version()`
Also undo some damage by clang-format in b624f32f94
* quantum/command.c: replace `print(…); print_{,val_}{dec,hex}*(…);` sequences with single `xprintf(…)`
`print_{dec,hex}*(…)` are just `#define`s for `xprintf(…)` anyway.
Each additional `xprintf(…)` costs ~8 bytes: the call instructions,
plus an additional NUL terminator.
This _really_ adds up: this commit saves 814 bytes on my ATmega32.
* quantum/command.c: optimise `mousekey_console()` for size & legibility
Made various tweaks to the interface, but still functionally identical.
Assume `KC_1`…`KC_0` to be contiguous, and removed `numkey2num(…)` entirely.
It was exported in `command.h` by 1a0bac8bcc for no obvious reason, before
which it was `static`. I doubt anyone uses it.
`mousekey_console()` is now enabled regardless of `MK_3_SPEED`.
Needs fleshing out for things other than the X11 variant though.
This commit saves 638 bytes on my ATmega32.
* disambiguate Bootmagic rules in keymaps
The files edited by this commit were added at a point in time where `BOOTMAGIC_ENABLE = yes` enabled full Bootmagic.
This commit edits the files to specify that full Bootmagic is intended.
* remove BOOTMAGIC_ENABLE=full setting
* unify commented BOOTMAGIC_ENABLE rules in keyboards
Explicitly sets `BOOTMAGIC_ENABLE = no` in keyboards where the rule was commented out.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;#[ \t]*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-zA-Z]\+\).*;\1 = no # Virtual DIP switch configuration;g' {} +
```
* remove commented Bootmagic rules from keymap/user level
Command:
```
find keyboards/ layouts/ users/ -type f -name 'rules.mk' -exec sed -i -e '/#.*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*/d' {} +
```
* update keyboard BOOTMAGIC_ENABLE rule formatting
Sets the formatting of BOOTMAGIC_ENABLE rules to `BOOTMAGIC_ENABLE = [value]`, without the inline comments (which will be replaced later).
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
```
* update keyboards' BOOTMAGIC_ENABLE settings
Updates keyboard `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = \)full;\1lite;g' '{}' +
```
* update keymap/user BOOTMAGIC_ENABLE settings
Updates keymap/user `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
```
* remove and replace inline comments in keyboards and keymap/user files
Removes and replaces the inline comments, which have been updated to read `Enable Bootmagic Lite`.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = lite\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = yes\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = no\);\1 # Enable Bootmagic Lite;g' '{}' +
```
* rename improperly named makefiles
Some files intended to be used as makefiles had improper names causing them to not be used as intended when building.
This commit corrects the filenames of the affected files.
* update renamed file with new rule formatting
* update QMK's template files
Updates QMK's `rules.mk` templates to use the new inline comment.
* update QMK Docs
- remove documentation of full Bootmagic
- update links to Bootmagic Lite doc
- add doc for Magic Keycodes
* rules.mk patch for coarse/ixora and coarse/vinta
* Combo processing improvements.
Now it is possible to use ModTap and LayerTap keys as part of combos.
Overlapping combos also don't trigger all the combos, just exactly the
one that you press.
New settings:
- COMBO_MUST_HOLD_MODS
- COMBO_MOD_TERM
- COMBO_TERM_PER_COMBO
- COMBO_MUST_HOLD_PER_COMBO
- COMBO_STRICT_TIMER
- COMBO_NO_TIMER
* Remove the size flags from combo_t struct boolean members.
This in the end actually saves space as the members are accessed so many
times. The amount of operations needed to access the bits uses more
memory than setting the size saves.
* Fix `process_combo_key_release` not called correctly with tap-only combos
* Fix not passing a pointer when NO_ACTION_TAPPING is defined.
* Docs for `COMBO_ONLY_FROM_LAYER`
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update quantum/process_keycode/process_combo.c
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Add `EXTRA_SHORT_COMBOS` option.
Stuff combo's `disabled` and `active` flags into `state`. Possibly can
save some space.
* Add more examples and clarify things with dict management system.
- Simple examples now has a combo that has modifiers included.
- The slightly more advanced examples now are actually more advanced
instead of just `tap_code16(<modded-keycode>)`.
- Added a note that `COMBO_ACTION`s are not needed anymore as you can
just use custom keycodes.
- Added a note that the `g/keymap_combo.h` macros use the
`process_combo_event` function and that it is not usable in one's
keymap afterwards.
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Change "the" combo action example to "email" example.
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Fix sneaky infinite loop with `combo_disable()`
No need to call `dump_key_buffer` when disabling combos because the
buffer is either being dumped if a combo-key was pressed, or the buffer is empty
if a non-combo-key is pressed.
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
* Update docs/feature_combo.md
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
Co-authored-by: precondition <57645186+precondition@users.noreply.github.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Add bootloader section to keyboard template
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Fix overflow in WPM calculations.
First, the "fresh" WPM calculation could end up being up to 12000 (with
default `WPM_ESTIMATED_WORD_SIZE`) if keys were pressed more or less
simultaneously. This value has now been clamped down to 255, in effect
clamping WPM to its max value of 255.
Second, with `WPM_ALLOW_COUNT_REGRESSION` enabled, it was possible to
regress the WPM below 0 (i.e. to 255) by just repeatedly pressing
backspace.
* Fix WPM being limited to 235 due to float/int logic.
This takes up about 700 bytes of space, and needs to be swapped to
opt-in, rather than opt-out. Build failures in general on AVR due to the
scarcity of available flash. People can re-enable it by adding to their
keymap's config.h files:
```
#define RGBLIGHT_EFFECT_TWINKLE
```
The prototype of matrix_output_unselect_delay() has been changed as follows.
```c
void matrix_output_unselect_delay(uint8_t line, bool key_pressed);
```
Currently, no keyboard seems to be redefining `matrix_output_unselect_delay()`, so there is no change in the system behavior.
With this change, the keyboard level code can get some optimization hints, for example, the following.
```c
void matrix_output_unselect_delay(uint8_t line, bool key_pressed) {
/* If none of the keys are pressed,
* there is no need to wait for time for the next line. */
if (key_pressed) {
#ifdef MATRIX_IO_DELAY
# if MATRIX_IO_DELAY > 0
wait_us(MATRIX_IO_DELAY);
# endif
#else
wait_us(30);
#endif
}
}
```
Two occurrences of `MATRIX_ROWS` weren't properly changed to
`ROWS_PER_HAND` in #13330, causing a crash during boot on at least my
Ergodox Infinity (including #13481).
* added support for inverting the hand pin for split keyboards
* Added docs about SPLIT_HAND_LOW_IS_LEFT
* Update docs/feature_split_keyboard.md
bring #define for split hand pin low for left half name in line with grid pin define
Co-authored-by: Joel Challis <git@zvecr.com>
* Update quantum/split_common/split_util.c
update split hand pin low is left name to match split hand grid define
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Avoid zero or overflow from user's rgb_matrix_config.speed
* Avoid zero tick for reactive splash.
* Avoid zero time for animation runner.
Co-authored-by: filterpaper <filterpaper@localhost>
* Extensible split data sync capability through transactions.
- Split common transport has been split up between the transport layer
and data layer.
- Split "transactions" model used, with convergence between I2C and
serial data definitions.
- Slave matrix "generation count" is used to determine if the full slave
matrix needs to be retrieved.
- Encoders get the same "generation count" treatment.
- All other blocks of data are synchronised when a change is detected.
- All transmissions have a globally-configurable deadline before a
transmission is forced (`FORCED_SYNC_THROTTLE_MS`, default 100ms).
- Added atomicity for all core-synced data, preventing partial updates
- Added retries to AVR i2c_master's i2c_start, to minimise the number of
failed transactions when interrupts are disabled on the slave due to
atomicity checks.
- Some keyboards have had slight modifications made in order to ensure
that they still build due to firmware size restrictions.
* Fixup LED_MATRIX compile.
* Parameterise ERROR_DISCONNECT_COUNT.
* Intended usage is data validation in split transport code.
* Default space efficient algorithm.
* Opt-in fast table based algorithmn with #define CRC8_USE_TABLE switch.
* Define switches for size and speed optimized versions, the default is size
optimized by using uint_least8_t as datatype for calculations.
* #define CRC8_OPTIMIZE_SPEED uses uint_fast8_t as datatype for
calculations, this only affects 32-bit Archs like ARM and RISC-V.
* Placeholder crc_init() function for hardware backed crc calculation,
not implemented yet.
* Set saturation limit to jellybean_raindrops_anim.h
* Use faster bit-shift maths and qadd8
* Remove extra parenthesis
* Single bitmask operation is sufficient.
Co-authored-by: filterpaper <filterpaper@localhost>
* Enable SPI1 for GMMK pro
* Setup initial boilerplate for new LED driver
* RGB matrix minimally functional
* Map full LED matrix
* Return keymap to default
* Fix printscreen LED mapping
* Reduce max brightness
* Default values for AW20216
* Add documentation for AW20216
* Disable console and warnings
* Run cformat
* Update drivers/awinic/aw20216.h
Co-authored-by: Drashna Jaelre <drashna@live.com>
* make aw struct match issi struct
Co-authored-by: Drashna Jaelre <drashna@live.com>
* add led location defines
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Use led pin definitions in keyboard.c
* Add driver indices to led map
* Fix elif typo
* Run cformat
* Update docs
* Fix typo in docs
* Document global brightness limits
Co-authored-by: Drashna Jaelre <drashna@live.com>
* Add fast_timer_t that is 16-bit or 32-bit based on architecture
A 16-bit timer will overflow sooner but be faster to compare on AVR.
* Avoid 8-bit timer overflows in debounce algorithms
Count down remaining elapsed time instead of trying to do 8-bit timer
comparisons.
Add a "none" implementation that is automatically used if DEBOUNCE is
0 otherwise it will break the _pk/_pr count down.
* Avoid unnecessary polling of the entire matrix in sym_eager_pk
The matrix only needs to be updated when a debounce timer expires.
* Avoid unnecessary polling of the entire matrix in sym_eager_pr
The matrix only needs to be updated when a debounce timer expires.
The use of the "needed_update" variable is trying to do what
"matrix_need_update" was added to fix but didn't work because it only
applied when all keys finished debouncing.
* Fix sym_defer_g timing inconsistency compared to other debounce algorithms
DEBOUNCE=5 should process the key after 5ms, not 6ms
* Add debounce tests
* Use memcmp to determine if matrix changed.
* Firmware size issues.
* Add documentation for the lack of need of MATRIX_ROW_PINS/MATRIX_COL_PINS, when overriding low-level matrix functions.
* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
Co-authored-by: Nick Brassel <nick@tzarc.org>
Tap dance callbacks may register weak mods; one case when it happens
is when a tap dance registers a key with modifiers. When the tap
dance is interrupted by pressing another key, these weak mods could
affect the interrupting key (normally any stale weak mods are cleared
at the start of action_exec() when handling a keypress event, but the
tap dance interrupt check code is called later, and the weak mods left
by that code were not cleared). Add another clear_weak_mods() call to
preprocess_tap_dance() to make sure that the interrupting keypress is
not affected by unrelated weak mods from the previous tap dance.
Fixes#12445.
The dac_basic driver did not work properly with `#define AUDIO_PIN A4`
(instead of configuring the A4 pin, the driver actually was switching
the A5 pin to analog mode, breaking any other usage of that pin in
addition to emitting a distorted signal on the improperly configured
A4 pin). Fix the code to configure the A4 pin as intended.
QMK Bot
CoffeeIsLife
Marek Wyborski
Ryan
Osamu Aoki
torkel104
Jouke Witteveen
FREEWING.JP
Nick Brassel
Stefan Kerkmann
Dasky
Drashna Jaelre
Thomas Kriechbaumer
precondition
SmugSam
Albert Y
yiancar
Pascal Getreuer
Yorick Peterse
Joel Challis
customMK
Simon Arlott
KoenGoe
uqs
Denis Savran
Michał Szczepaniak
jack
ZiTe
Gompa
Takeshi ISHII
Joakim Tufvegren
MasterSpoon
Desprez Jean-Marc
Adam Lickel
Pete Sevander
Ga68
KraXen72
Ryan Hausen
Alabastard-64
Leo Deng
Jay Greco
Erik Berthold
Chad Austin
vectorstorm
Chris Broekema
billybraga
Yoichiro Tanaka
Dipl.-Ing. Raoul Rubien, BSc
Karl Shea
wheredoesyourmindgo
Isaac Elenbaas
Zach White
Balz Guenat
Mikkel Jeppesen
Markus Fritsche
Purdea Andrei
lalalademaxiya1
Woody
Vlad K
Sergey Vlasov
Marcus van Houdt
Thomas Weißschuh
JayceFayne
Xelus22
Donald Kjer
Olli Helenius
Path Nirvana
Joakim Tufvegren
XScorpion2
tucvbif
a-chol
freqmod
thpoll83
Liyang HU
James Young
Patrick Stadler
Carl-Fredrik Arvidson
Johannes Choo
Chris Cullin
Jonas Gessner
Jameson Thatcher
Gigahawk
Erovia
Michael Stapelberg
Matthes W
github-actions[bot]
Daniel Rodríguez Rivero
Joshua Diamond