The `adc_read()` code for STM32F0xx expects to get the 0-based channel
number in `mux.input`, but the `pinToMux()` code for STM32F0xx was
attempting to pass the CHSELR bit mask in that field, which resulted in
selecting a wrong channel, therefore `analogReadPin()` did not work
properly for the STM32F0xx chips. Fix `pinToMux()` to put the channel
number in that field (this matches the behavior for other supported
chips and also allows selection of channels 16...18, which can be used
to access the builtin temperature, reference voltage and VBAT sensors).
* Rename `eeprom_stm32` to `eeprom_legacy_emulated_flash`.
* Rename `flash_stm32` to `legacy_flash_ops`.
* Rename `eeprom_teensy` to `eeprom_kinetis_flexram`.
...by moving the actually timing critical `enter_rx_state()` and
`leave_rx_state()` functions to RAM in order to not be affected by XIP
cache spikes. This commit also reverts the hacky USB interrupt disabling
that was done in 293c53d774
* Add ARRAY_SIZE and CEILING utility macros
* Apply a coccinelle patch to use ARRAY_SIZE
* fix up some straggling items
* Fix 'make test:secure'
* Enhance ARRAY_SIZE macro to reject acting on pointers
The previous definition would not produce a diagnostic for
```
int *p;
size_t num_elem = ARRAY_SIZE(p)
```
but the new one will.
* explicitly get definition of ARRAY_SIZE
* Convert to ARRAY_SIZE when const is involved
The following spatch finds additional instances where the array is
const and the division is by the size of the type, not the size of
the first element:
```
@ rule5a using "empty.iso" @
type T;
const T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
@ rule6a using "empty.iso" @
type T;
const T[] E;
@@
- sizeof(E)/sizeof(T)
+ ARRAY_SIZE(E)
```
* New instances of ARRAY_SIZE added since initial spatch run
* Use `ARRAY_SIZE` in docs (found by grep)
* Manually use ARRAY_SIZE
hs_set is expected to be the same size as uint16_t, though it's made
of two 8-bit integers
* Just like char, sizeof(uint8_t) is guaranteed to be 1
This is at least true on any plausible system where qmk is actually used.
Per my understanding it's universally true, assuming that uint8_t exists:
https://stackoverflow.com/questions/48655310/can-i-assume-that-sizeofuint8-t-1
* Run qmk-format on core C files touched in this branch
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
From the ChibiOS HAL I2C driver pages:
After a timeout the driver must be stopped and restarted because the bus is in
an uncertain state.
This commit does that stopping explicitly on any error that occurred, not only
timeouts. As all the i2c functions restart the peripheral if necessary it is
safe to do so.
Co-authored-by: Dasky <32983009+daskygit@users.noreply.github.com>
Co-authored-by: Dasky <32983009+daskygit@users.noreply.github.com>
* Use polled waiting on platforms that support it
Due to context switching overhead waiting a very short amount of time on
a sleeping thread is often not accurate and in fact not usable for timing
critical usage i.e. in a driver. Thus we use polled waiting for ranges
in the us range on platforms that support it instead. The fallback is
the thread sleeping mechanism.
This includes:
* ARM platforms with CYCCNT register (ARMv7, ARMv8) this is
incremented at CPU clock frequency
* GD32VF103 RISC-V port with CSR_MCYCLE register this is incremented at
CPU clock frequency
* RP2040 ARMv6 port which uses the integrated timer peripheral which is
incremented with a fixed 1MHz frequency
* Use wait_us() instead of chSysPolledDelayX
...as it is powered by busy waiting now.
* Add chibios waiting methods test bench
* Disable RESET keycode because of naming conflicts
* Add Pico SDK as submodule
* Add RP2040 build support to QMK
* Adjust USB endpoint structs for RP2040
* Add RP2040 bootloader and double-tap reset routine
* Add generic and pro micro RP2040 boards
* Add RP2040 onekey keyboard
* Add WS2812 PIO DMA enabled driver and documentation
Supports regular and open-drain output configuration. RP2040 GPIOs are
sadly not 5V tolerant, so this is a bit use-less or needs extra hardware
or you take the risk to fry your hardware.
* Adjust SIO Driver for RP2040
* Adjust I2C Driver for RP2040
* Adjust SPI Driver for RP2040
* Add PIO serial driver and documentation
* Add general RP2040 documentation
* Apply suggestions from code review
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Drashna Jaelre
Ryan
Nick Brassel
Marek Kraus
Sergey Vlasov
Stefan Kerkmann
David Hoelscher
jack
Joy Lee
Thomas Kriechbaumer
Jeff Epler
Joel Challis
yiancar
Joy Lee
QMK Bot