* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
* Fixed slave-side keyboard half unresponsiveness
due to how LUFA handles USB_Disable()
* changes to formatting
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Avoid NO_USB_STARTUP_CHECK - Disable USB as checks seem to enable it somehow
* Update quantum/split_common/split_util.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Also remove NO_USB_STARTUP_CHECK from vitamins_included/rev1
* Add support for wiring RGB LEDs for both halves directly to their respective controllers
RGB LEDs for each half don't need to be chained together across the TRRS cable with this
* Add split RGB LED support for serial
* Update config/rules for bakingpy layout
* Un-nest ifdefs for hand detection
* Read RGB config state from memory instead of EEPROM for serial updates
* Reuse existing LED pointer instead of creating new one
* Eliminate separate slave loop
Both master and slave run the standard keyboard_task main loop now.
* Refactor i2c/serial specific code
Simplify some of the preprocessor mess by using common function names.
* Fix missing #endif
* Move direct pin mapping support from miniaxe to split_common
For boards with more pins than sense--sorry, switches.
* Reordering and reformatting only
* Don't run matrix_scan_quantum on slave side
* Clean up the offset/slaveOffset calculations
* Cut undebounced matrix size in half
* Refactor debouncing
* Minor fixups
* Split split_common transport and debounce code into their own files
Can now be replaced with custom versions per keyboard using
CUSTOM_TRANSPORT = yes and CUSTOM_DEBOUNCE = yes
* Refactor debounce for non-split keyboards too
* Update handwired/xealous to build using new split_common
* Fix debounce breaking basic test
* Dodgy method to allow a split kb to only include one of i2c/serial
SPLIT_TRANSPORT = serial or SPLIT_TRANSPORT = i2c will include only
that driver code in the binary.
SPLIT_TRANSPORT = custom (or anything else) will include neither, the
keyboard must supply it's own code
if SPLIT_TRANSPORT is not defined then the original behaviour (include
both avr i2c and serial code) is maintained.
This could be better but it would require explicitly updating all the
existing split keyboards.
* Enable LTO to get lets_split/sockets under the line
* Add docs for SPLIT_TRANSPORT, CUSTOM_MATRIX, CUSTOM_DEBOUNCE
* Remove avr-specific sei() from split matrix_setup
Not needed now that slave doesn't have a separate main loop.
Both sides (on avr) call sei() in lufa's main() after exiting
keyboard_setup().
* Fix QUANTUM_LIB_SRC references and simplify SPLIT_TRANSPORT.
* Add comments and fix formatting.
* Add provisional Helix implementation to test the quantum/split_common.
* copy keyboards/helix/serial.[ch] to quantum/split_common/
* Make serial.c a pure driver.
Remove buffer name and buffer size from serial.c. They should be placed in the caller(matrix.c, split_utils.c).
* remove quantum/split_common/serial_backward_compatibility.h
* Changed array serial_master_buffer to structure serial_m2s_buffer.
* Changed array serial_slave_buffer to structure serial_s2m_buffer.
* Change keyboards/miniaxe/matrix.c
I also made changes to quantum/split_comon/matrix.c to keyboards/miniaxe/matrix.c.
Note: I contacted @ka2hiro, creator of miniaxe, and I got permission to change keyboards/miniaxe/matrix.c.
* update history comment in quantum/split_common/serial.c
* Revert "Add provisional Helix implementation to test the quantum/split_common."
This reverts commit 168c82ef82c88e79979d9796bab9cc819cc2f685.
* fix keyboards/miniaxe/matrix.c, quantum/split_common/matrix.c
avr-gcc 4.9.[23] report error.
avr-gcc 5.4.0, avr-gcc 7.3.0 pass.
It is funny.
* update comment quantum/split_common/serial.c
* Reserve RGBLIGHT_SPLIT macro in quantum/split_common
Added JTAG disable code to the split_common slave code since the slave never calls keyboard_init(). In the future the slave should likely be modified to call keyboard_init() in some way, but without calling any of the unnecessary USB initialization code.
* Line ending stuff again
* Added Let's Split Eh? Files and updated #USE_IC2 checks to also include th EH revision (can only be used in I2C)
* Added personal keymap, updated some of the EH files
* Created new keyboard file for testing "lets_split_eh" will merge into lets_split once fully functional
* Added split code from lets_split, removed pro micro imports and LED code
THIS IS WORKING CODE, WITHOUT RGB AND BACKLIGHT
* Took back original Lets Slit files for the lets_split keyboard, working in the lets_split_eh folder for now
* Updated eh.c
* More rework of the I2C code, added global flags for split boards.
* Introduced RGB over I2C, having weird edge case issues at the moment though
* Fixed weird I2C edgecase with RGB, although still would like to track down route cause..
* Changed RGB keycodes (static ones) to activate on key-up instead of key-down to elimate weird ghosting issue over I2C
* Lots of changes, mainly externalized the Split keyboard code and added logic for only including when needed.
- Added makefile option "SPLIT_KEYBOARD" that when = yes will include the split keyboard files and custom matrix
- Split keyboard files placed into quantum/split_common/
- Added define option for config files "SPLIT_HAND_PIN" FOr using high/low pin to determine handedness, low = right hand, high = left hand
- Cleaned up split logic for RGB and Backlight so it is only exectuted / included when needed
* Updated documentation for the new makefile options and #defines specific to split keyboards
* Added a bit more info to docs, so people aren't confused
* Modifed Let's Split to use externalized code, also added left and right hand eeprom files to the split_common folder
* Removed some debugging from eh.c
* Small changes to keyboard configs. Also added a default keymap (just a copy of my that_canadian keymap).
* Added a README file to the Let's Split Eh?
* Changed it so RGB static updates are done on key-up ONLY for split boards rather than all boards. Also fixed leftover un-used variable in rgblight.c
* Updated default keymap and my keymap for Let's Split Eh? Updated the comments so it reflects RGB control, and removed audio functions.
* Fixed lets_split_eh not having a default version
* Removed "eh" references from lets_split folder for now
* Took lets_split folder from master to fix travis build errors, weird my local was overriding.
* Changed LAYOUT_ortho_4x12_kc -> LAYOUT_kc_ortho_4x12 to match bakingpy and others
* Removed rules.mk from my lets_split keymap, not needed
* Updated the config_options doc to better explain the usage of "#define SPLIT_HAND_PIN"
* Fixed split_common assuming I2C for RGB and Backlight. Added serial backlight support (stole from bakingpy's Levinson code ;) ) Serial RGB not implemented yet. Also Added "USE_IC2" to the lets_split_eh/eh as that was looked over.
* Fixed stupid mistake, forgot to set BACKLIT_DIRTY to false after setting slave backlit settings for serial
* Updated backlight data block to be cleaner (thanks drashna ;) )
* Line ending stuff again
* Added Let's Split Eh? Files and updated #USE_IC2 checks to also include th EH revision (can only be used in I2C)
* Added personal keymap, updated some of the EH files
* Created new keyboard file for testing "lets_split_eh" will merge into lets_split once fully functional
* Added split code from lets_split, removed pro micro imports and LED code
THIS IS WORKING CODE, WITHOUT RGB AND BACKLIGHT
* Took back original Lets Slit files for the lets_split keyboard, working in the lets_split_eh folder for now
* Updated eh.c
* More rework of the I2C code, added global flags for split boards.
* Introduced RGB over I2C, having weird edge case issues at the moment though
* Fixed weird I2C edgecase with RGB, although still would like to track down route cause..
* Changed RGB keycodes (static ones) to activate on key-up instead of key-down to elimate weird ghosting issue over I2C
* Lots of changes, mainly externalized the Split keyboard code and added logic for only including when needed.
- Added makefile option "SPLIT_KEYBOARD" that when = yes will include the split keyboard files and custom matrix
- Split keyboard files placed into quantum/split_common/
- Added define option for config files "SPLIT_HAND_PIN" FOr using high/low pin to determine handedness, low = right hand, high = left hand
- Cleaned up split logic for RGB and Backlight so it is only exectuted / included when needed
* Updated documentation for the new makefile options and #defines specific to split keyboards
* Added a bit more info to docs, so people aren't confused
* Modifed Let's Split to use externalized code, also added left and right hand eeprom files to the split_common folder
* Removed some debugging from eh.c
* Small changes to keyboard configs. Also added a default keymap (just a copy of my that_canadian keymap).
* Added a README file to the Let's Split Eh?
* Changed it so RGB static updates are done on key-up ONLY for split boards rather than all boards. Also fixed leftover un-used variable in rgblight.c
* Updated default keymap and my keymap for Let's Split Eh? Updated the comments so it reflects RGB control, and removed audio functions.
* Fixed lets_split_eh not having a default version
* Removed "eh" references from lets_split folder for now
* Took lets_split folder from master to fix travis build errors, weird my local was overriding.
* Changed LAYOUT_ortho_4x12_kc -> LAYOUT_kc_ortho_4x12 to match bakingpy and others
* Removed rules.mk from my lets_split keymap, not needed
* Updated the config_options doc to better explain the usage of "#define SPLIT_HAND_PIN"
James Young
Ryan
sol
Takeshi ISHII
Adrian
Nick Brassel
Joel Challis
Danny
skullY
James Churchill
Drashna Jaelre
Danny Nguyen
That-Canadian
Chiang Fong Lee