307 lines
8.3 KiB
Markdown
307 lines
8.3 KiB
Markdown
# PS/2 Mouse Support :id=ps2-mouse-support
|
|
|
|
Its possible to hook up a PS/2 mouse (for example touchpads or trackpoints) to your keyboard as a composite device.
|
|
|
|
To hook up a Trackpoint, you need to obtain a Trackpoint module (i.e. harvest from a Thinkpad keyboard), identify the function of each pin of the module, and make the necessary circuitry between controller and Trackpoint module. For more information, please refer to [Trackpoint Hardware](https://deskthority.net/wiki/TrackPoint_Hardware) page on Deskthority Wiki.
|
|
|
|
There are three available modes for hooking up PS/2 devices: USART (best), interrupts (better) or busywait (not recommended).
|
|
|
|
## The Circuitry between Trackpoint and Controller :id=the-circuitry-between-trackpoint-and-controller
|
|
|
|
To get the things working, a 4.7K drag is needed between the two lines DATA and CLK and the line 5+.
|
|
|
|
```
|
|
|
|
DATA ----------+--------- PIN
|
|
|
|
|
4.7K
|
|
|
|
|
MODULE 5+ --------+--+--------- PWR CONTROLLER
|
|
|
|
|
4.7K
|
|
|
|
|
CLK ------+------------ PIN
|
|
```
|
|
|
|
|
|
## Busywait Version :id=busywait-version
|
|
|
|
Note: This is not recommended, you may encounter jerky movement or unsent inputs. Please use interrupt or USART version if possible.
|
|
|
|
In rules.mk:
|
|
|
|
```makefile
|
|
PS2_MOUSE_ENABLE = yes
|
|
PS2_USE_BUSYWAIT = yes
|
|
```
|
|
|
|
In your keyboard config.h:
|
|
|
|
```c
|
|
#ifdef PS2_USE_BUSYWAIT
|
|
# define PS2_CLOCK_PORT PORTD
|
|
# define PS2_CLOCK_PIN PIND
|
|
# define PS2_CLOCK_DDR DDRD
|
|
# define PS2_CLOCK_BIT 1
|
|
# define PS2_DATA_PORT PORTD
|
|
# define PS2_DATA_PIN PIND
|
|
# define PS2_DATA_DDR DDRD
|
|
# define PS2_DATA_BIT 2
|
|
#endif
|
|
```
|
|
|
|
## Interrupt Version :id=interrupt-version
|
|
|
|
The following example uses D2 for clock and D5 for data. You can use any INT or PCINT pin for clock, and any pin for data.
|
|
|
|
In rules.mk:
|
|
|
|
```makefile
|
|
PS2_MOUSE_ENABLE = yes
|
|
PS2_USE_INT = yes
|
|
```
|
|
|
|
In your keyboard config.h:
|
|
|
|
```c
|
|
#ifdef PS2_USE_INT
|
|
#define PS2_CLOCK_PORT PORTD
|
|
#define PS2_CLOCK_PIN PIND
|
|
#define PS2_CLOCK_DDR DDRD
|
|
#define PS2_CLOCK_BIT 2
|
|
#define PS2_DATA_PORT PORTD
|
|
#define PS2_DATA_PIN PIND
|
|
#define PS2_DATA_DDR DDRD
|
|
#define PS2_DATA_BIT 5
|
|
|
|
#define PS2_INT_INIT() do { \
|
|
EICRA |= ((1<<ISC21) | \
|
|
(0<<ISC20)); \
|
|
} while (0)
|
|
#define PS2_INT_ON() do { \
|
|
EIMSK |= (1<<INT2); \
|
|
} while (0)
|
|
#define PS2_INT_OFF() do { \
|
|
EIMSK &= ~(1<<INT2); \
|
|
} while (0)
|
|
#define PS2_INT_VECT INT2_vect
|
|
#endif
|
|
```
|
|
|
|
## USART Version :id=usart-version
|
|
|
|
To use USART on the ATMega32u4, you have to use PD5 for clock and PD2 for data. If one of those are unavailable, you need to use interrupt version.
|
|
|
|
In rules.mk:
|
|
|
|
```makefile
|
|
PS2_MOUSE_ENABLE = yes
|
|
PS2_USE_USART = yes
|
|
```
|
|
|
|
In your keyboard config.h:
|
|
|
|
```c
|
|
#ifdef PS2_USE_USART
|
|
#define PS2_CLOCK_PORT PORTD
|
|
#define PS2_CLOCK_PIN PIND
|
|
#define PS2_CLOCK_DDR DDRD
|
|
#define PS2_CLOCK_BIT 5
|
|
#define PS2_DATA_PORT PORTD
|
|
#define PS2_DATA_PIN PIND
|
|
#define PS2_DATA_DDR DDRD
|
|
#define PS2_DATA_BIT 2
|
|
|
|
/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
|
|
/* set DDR of CLOCK as input to be slave */
|
|
#define PS2_USART_INIT() do { \
|
|
PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
|
|
PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
|
|
UCSR1C = ((1 << UMSEL10) | \
|
|
(3 << UPM10) | \
|
|
(0 << USBS1) | \
|
|
(3 << UCSZ10) | \
|
|
(0 << UCPOL1)); \
|
|
UCSR1A = 0; \
|
|
UBRR1H = 0; \
|
|
UBRR1L = 0; \
|
|
} while (0)
|
|
#define PS2_USART_RX_INT_ON() do { \
|
|
UCSR1B = ((1 << RXCIE1) | \
|
|
(1 << RXEN1)); \
|
|
} while (0)
|
|
#define PS2_USART_RX_POLL_ON() do { \
|
|
UCSR1B = (1 << RXEN1); \
|
|
} while (0)
|
|
#define PS2_USART_OFF() do { \
|
|
UCSR1C = 0; \
|
|
UCSR1B &= ~((1 << RXEN1) | \
|
|
(1 << TXEN1)); \
|
|
} while (0)
|
|
#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1))
|
|
#define PS2_USART_RX_DATA UDR1
|
|
#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
|
|
#define PS2_USART_RX_VECT USART1_RX_vect
|
|
#endif
|
|
```
|
|
|
|
## Additional Settings :id=additional-settings
|
|
|
|
### PS/2 Mouse Features :id=ps2-mouse-features
|
|
|
|
These enable settings supported by the PS/2 mouse protocol.
|
|
|
|
```c
|
|
/* Use remote mode instead of the default stream mode (see link) */
|
|
#define PS2_MOUSE_USE_REMOTE_MODE
|
|
|
|
/* Enable the scrollwheel or scroll gesture on your mouse or touchpad */
|
|
#define PS2_MOUSE_ENABLE_SCROLLING
|
|
|
|
/* Some mice will need a scroll mask to be configured. The default is 0xFF. */
|
|
#define PS2_MOUSE_SCROLL_MASK 0x0F
|
|
|
|
/* Applies a transformation to the movement before sending to the host (see link) */
|
|
#define PS2_MOUSE_USE_2_1_SCALING
|
|
|
|
/* The time to wait after initializing the ps2 host */
|
|
#define PS2_MOUSE_INIT_DELAY 1000 /* Default */
|
|
```
|
|
|
|
You can also call the following functions from ps2_mouse.h
|
|
|
|
```c
|
|
void ps2_mouse_disable_data_reporting(void);
|
|
|
|
void ps2_mouse_enable_data_reporting(void);
|
|
|
|
void ps2_mouse_set_remote_mode(void);
|
|
|
|
void ps2_mouse_set_stream_mode(void);
|
|
|
|
void ps2_mouse_set_scaling_2_1(void);
|
|
|
|
void ps2_mouse_set_scaling_1_1(void);
|
|
|
|
void ps2_mouse_set_resolution(ps2_mouse_resolution_t resolution);
|
|
|
|
void ps2_mouse_set_sample_rate(ps2_mouse_sample_rate_t sample_rate);
|
|
```
|
|
|
|
### Fine Control :id=fine-control
|
|
|
|
Use the following defines to change the sensitivity and speed of the mouse.
|
|
Note: you can also use `ps2_mouse_set_resolution` for the same effect (not supported on most touchpads).
|
|
|
|
```c
|
|
#define PS2_MOUSE_X_MULTIPLIER 3
|
|
#define PS2_MOUSE_Y_MULTIPLIER 3
|
|
#define PS2_MOUSE_V_MULTIPLIER 1
|
|
```
|
|
|
|
### Scroll Button :id=scroll-button
|
|
|
|
If you're using a trackpoint, you will likely want to be able to use it for scrolling.
|
|
It's possible to enable a "scroll button/s" that when pressed will cause the mouse to scroll instead of moving.
|
|
To enable the feature, you must set a scroll button mask as follows:
|
|
|
|
```c
|
|
#define PS2_MOUSE_SCROLL_BTN_MASK (1<<PS2_MOUSE_BTN_MIDDLE) /* Default */
|
|
```
|
|
|
|
To disable the scroll button feature:
|
|
|
|
```c
|
|
#define PS2_MOUSE_SCROLL_BTN_MASK 0
|
|
```
|
|
|
|
The available buttons are:
|
|
|
|
```c
|
|
#define PS2_MOUSE_BTN_LEFT 0
|
|
#define PS2_MOUSE_BTN_RIGHT 1
|
|
#define PS2_MOUSE_BTN_MIDDLE 2
|
|
```
|
|
|
|
You can also combine buttons in the mask by `|`ing them together.
|
|
|
|
Once you've configured your scroll button mask, you must configure the scroll button send interval.
|
|
This is the interval before which if the scroll buttons were released they would be sent to the host.
|
|
After this interval, they will cause the mouse to scroll and will not be sent.
|
|
|
|
```c
|
|
#define PS2_MOUSE_SCROLL_BTN_SEND 300 /* Default */
|
|
```
|
|
|
|
To disable sending the scroll buttons:
|
|
|
|
```c
|
|
#define PS2_MOUSE_SCROLL_BTN_SEND 0
|
|
```
|
|
|
|
Fine control over the scrolling is supported with the following defines:
|
|
|
|
```c
|
|
#define PS2_MOUSE_SCROLL_DIVISOR_H 2
|
|
#define PS2_MOUSE_SCROLL_DIVISOR_V 2
|
|
```
|
|
|
|
### Invert Mouse and Scroll Axes :id=invert-mouse-and-scroll-axes
|
|
|
|
To invert the X and Y axes you can put:
|
|
|
|
```c
|
|
#define PS2_MOUSE_INVERT_X
|
|
#define PS2_MOUSE_INVERT_Y
|
|
```
|
|
|
|
into config.h.
|
|
|
|
To reverse the scroll axes you can put:
|
|
|
|
```c
|
|
#define PS2_MOUSE_INVERT_H
|
|
#define PS2_MOUSE_INVERT_V
|
|
```
|
|
|
|
into config.h.
|
|
|
|
### Rotate Mouse Axes :id=rotate-mouse-axes
|
|
|
|
Transform the output of the device with a clockwise rotation of 90, 180, or 270
|
|
degrees.
|
|
|
|
When compensating for device orientation, rotate the output the same amount in
|
|
the opposite direction. E.g. if the normal device orientation is considered to
|
|
be North-facing, compensate as follows:
|
|
|
|
```c
|
|
#define PS2_MOUSE_ROTATE 270 /* Compensate for East-facing device orientation. */
|
|
```
|
|
```c
|
|
#define PS2_MOUSE_ROTATE 180 /* Compensate for South-facing device orientation. */
|
|
```
|
|
```c
|
|
#define PS2_MOUSE_ROTATE 90 /* Compensate for West-facing device orientation. */
|
|
```
|
|
|
|
### Debug Settings :id=debug-settings
|
|
|
|
To debug the mouse, add `debug_mouse = true` or enable via bootmagic.
|
|
|
|
```c
|
|
/* To debug the mouse reports */
|
|
#define PS2_MOUSE_DEBUG_HID
|
|
#define PS2_MOUSE_DEBUG_RAW
|
|
```
|
|
|
|
### Movement Hook :id=movement-hook
|
|
|
|
Process mouse movement in the keymap before it is sent to the host. Example
|
|
uses include filtering noise, adding acceleration, and automatically activating
|
|
a layer. To use, define the following function in your keymap:
|
|
|
|
```c
|
|
void ps2_mouse_moved_user(report_mouse_t *mouse_report);
|
|
```
|