qmk-dactyl-manuform-a/keyboards/handwired/z150/readme.md

63 lines
2.9 KiB
Markdown
Raw Blame History

This file contains ambiguous Unicode characters!

This file contains ambiguous Unicode characters that may be confused with others in your current locale. If your use case is intentional and legitimate, you can safely ignore this warning. Use the Escape button to highlight these characters.

# QMK-based firmware for Zenith Z-150 keyboard
![Z-150](https://imgur.com/jayyyvJ.jpg)
Zenith Z-150 keyboard conversion project: direct connection of Black Pill to the matrix.
* Keyboard Maintainer: [DmNosachev](https://github.com/DmNosachev)
* Hardware Supported: [Zenith Z-150 keyboard, 100-1860 version with white logo](https://deskthority.net/wiki/Zenith_Z-150), Black Pill STM32F103C8T6 MCU board. Alternatevely you can use any MCU which is supported by QMK and has 22 or more IO pins: Arduino Micro, Teensy 2.0, Teensy 2.0++, Blue Pill, etc.
Earlier 100-1886 version with black logo has different PCB.
Make example for this keyboard (after setting up your build environment):
make handwired/z150:default
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
# Modding
## Matrix
Z-150 has 11x8 matrix. It's ghost-free thanks to the diodes.
Columns are located under NEC D8049HC MCU IC:
![Z-150 columns](https://imgur.com/XiOsrnh.jpg)
Rows are connected to unmarked 24-pin MUX IC:
![Z-150 rows](https://imgur.com/Wu8rHY0.jpg)
## LEDs
LEDs (from left to right): NumLock, CapsLock, ScrollLock:
![Z-150 LED cathodes](https://imgur.com/MO5NLlZ.jpg)
Their anodes are connected to VCC through 220Ω resistors.
![Z-150 LED anodes](https://imgur.com/w1MfjRN.jpg)
You can keep the original resistors, but with Black Pill or any other 3.3V controller the LEDs may seem a little dim. Try 150Ω or close value if you want to fix that.
## Black Pill
Suggested mount position for the Black Pill (view from the bottom side of the PCB):
```
R0 R1 R2 R3 R4 R6 R9 LC LN LS
,--------------------------------------------------------------------,
|B12 B13 B14 B15 A8 A9 A10 A11 A12 A15 B3 B4 B5 B6 B7 3V3 GND |---,
| |USB|
|B11 B10 B1 B0 A7 A6 A5 A4 A3 A2 A1 A0 RST C13 B9 B8 GND |---'
'--------------------------------------------------------------------'
C0 C1 C2 C3 C4 C5 C6 C7 R5 R8 R7 RA
```
1. Desolder all ICs, crystal oscillator, capacitors and resistors except R0R2 (they connect LEDs to VCC).
1. Solder 12-pin header to the Black Pill (pins B11A0 on the left side).
2. Solder two 3-pin headers for boot jumpers.
3. Solder 4-pin SWD header.
4. Burn [STM32duino bootloader](https://github.com/rogerclarkmelbourne/STM32duino-bootloader/blob/master/bootloader_only_binaries/generic_boot20_pb12.bin) to Black Pill.
5. Compile and flash the firmware: `make handwired/z150:default:flash`
5. Align Black Pill pins B11A4 with columns 07 and solder them.
6. Connect rows, LEDs, ground and VCC traces to the corresponding pins of the BlackPill using additional wires.