* Error out when Solenid pin is not defined
Instead of defaulting to a (literally) random pin, error out instead. Because this pin may be used, or because that pin may not be exposed, or may not exist.
* Remove 'SOLENOID_ACTIVE' setting since it's not used
* Update documentation
* Move Ergodox EZ RGB code to custom driver
Also implements full addressing of Ergodox EZ's LED Strip, as written by seebs
Co-authored-by: Seebs <seebs@seebs.net>
* Make Clipping range accessible for custom drivers
* Remove RGBW_BB_TWI from driver and docs
* Revert changes to clipping range support
* Use just rgblight_set instead of full custom driver
* Convert to i2c_master commands
* Rename rgblight driver and clean up includes
* Fix unicode in comments
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Remove separate RGBW implementation for a unified function
* Set White to 0 in RGBW LEDs
This is just to get this working, later, proper brightness can be handled elsewhere.
* Use us instead of nanoseconds(?) since it renders correctly on web
* Remove RGBW function from arm/ws2812.h
* Remove RGBW function from arm/ws2812.c
* Formatting changes
* Add doc info
* Initial ARM bitbang ws2812 driver
* Unify chibios platform to run rgblight_task
* Remove 'avr only' comments from ws2812 docs
* Remove 'avr only' comments from ws2812 docs
* Unify chibios platform to run rgblight_task - review comments
* Remove debug flags from keymap
* Add comments from review
* Add defines for STM32L0XX
* Attempt to get arm ws2812 working on multiple gcc versions
It was beleaved that this setting result in a 400Khz I2C bus.
This was incorrect, actual frequency measure with a logic analyzer was around 150Khz.
This is derived from the excel sheet linked in the .h file.
Also confirmed with the ST IDE.
* Began Work On STM32 Ergodox
Changes to be committed:
new file: keyboards/ergodox_stm32/config.h
new file: keyboards/ergodox_stm32/rules.mk
* test
* Now it compile. Not linking thou
* Screw this Linker. It links now!
* Blinkly Keyboard
* bootloader test code
* Working on matrix / i2c stuff
* Progress (LED Blink)
* Progress on MCP_23017 Status Flag
* [WIP]
* update
* Works! Remeber to change back the bootloader address when the new bootloadrer is ready.
* Time to go debug the i2c
* Finally, it now works with PCB Rev 1.0.2
* updated for rev.2 pcb
* minor compilation fix
* Why when debugger is enabled then everything works.
* Remeber to call init functions.
* Update arm i2c driver to support STM32F103 series device.
* fix include once header. Replaced with #pragma once.
* complication test
* provide means to turn on RTP mode and set the amplitude
* new keycode HPT_CONT to turn RTP off/on
* introduce new keycodes HPT_CONI, and HPT_COND for Haptic Continuous Increase and Decrease
* support for continuous mode amplitude increase and decrease
* code cleanup
* update docs to reference new keycodes and functionality
* don't touch the keymaps
* add function prototypes
* add proper guards
* cleanup guards
* remove extra reserved
* Fix battery level code in adafruit_ble.cpp
The code in tsk_core/protocol/lufa/adafluit_ble.cpp that polls the
battery level for the Adafruit feather BLE controller reads the
regulated voltage, not the raw voltage coming from the battery. To do
that, the Adafruit Feather docs say you should read from pin A9:
https://learn.adafruit.com/adafruit-feather-32u4-basic-proto/power-management#measuring-battery-4-9.
(See also
https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le/pinouts#logic-pins-2-9.)
I'm not sure why, but analogRead(9); doesn't read the correct pin.
Checking all available analog pins experimentally, it turns out that
analogRead(7); returns the correct value. So the code above should read:
state.vbat = analogRead(7);
* Update tmk_core/protocol/lufa/adafruit_ble.cpp
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Remove old comment
* Fix linking error
* Remove `#ifdef` around `#include analog.h`.
* Really fix linking error
Currently OLED Dirver only supports LF (\n) character in a string to clear out the rest of the current line and advance to the next line for writing. This PR adds support for CR (\r) character as well to advance to the next line, however not clear out the rest of the current line. This is extremely useful when you want to display a multi-line logo using a single array without wiping out exiting lines and flagging the OLED as dirty unnecessarily.
Using QUANTUM_LIB_SRC prevents the warning when multiple sources add the i2c_master.c file. Boards such as the Ergodox EZ Glow see this warning every time they compile because the board uses the file in general, and because the RGB LED Matrix requires it, as well.
* modify oled_driver to support SH1106
also:
- improve mechanism to specify which OLED IC we use
- comment calc_bounds()
- give OLED_COLUMN_OFFSET a default value
- inline comment re: OLED MEMORY_MODE and SH1106
- update docs/feature_oled_driver.h for SH1106 support and related changes
- docs: OLED: note we have tested SSD1306 on ARM boards (per @XScorpion2)
- define out MEMORY_MODE when using SH1106 OLED driver
* document that SSD1306 128x64 on AVR works
Per @XScorpion2: https://github.com/qmk/qmk_firmware/pull/5787#discussion_r291837842
I2C timing parameters were seemingly set up for an STM32F303 target MCU, at a specific clock speed. This commit allows specifying the timing parameters via config.h, allowing other STM32 MCUs to be targeted, potentially at different clock frequencies.
Alternate function modes for the I2C pins are now also configurable, allowing for remapping to other pins.
* RGB Matrix overhaul
Breakout of animations to separate files
Integration of optimized int based math lib
Overhaul of rgb_matrix.c and animations for performance
* Updating effect function api for future extensions
* Combined the keypresses || keyreleases define checks into a single define so I stop forgetting it where necessary
* Moving define RGB_MATRIX_KEYREACTIVE_ENABLED earlier in the include chain
* Adds the Planck EZ, 3737 RGB, fixes out-of-tune notes
* fix bug in quantum/rgb_matrix_drivers.c
Co-Authored-By: jackhumbert <jack.humb@gmail.com>
* update command setting to the correct default
* correct rgb config
* remove commented-out lines
* update docs for the 3737
* Update docs/feature_rgb_matrix.md
Co-Authored-By: jackhumbert <jack.humb@gmail.com>
* On i2c_init, enable two wire interface, twi interrupt, and slave
address ACK along with pull up resistors.
* thanks to some testing by drashna, we know that setting TWI doesn't work for all boards. Putting the new code into an ifdef block
* initial work to add eeprom to haptic feedback and decouple the feedback process from keyboards
* Haptic feedback enhancements: on/off toggle working, feedback order working
todo:
-work on modes switching
-get modes switching to save to eeprom
* haptic enhancement - eeprom and modes added
* Added set and get functions for haptic feedback
* initial implementation of solenoids under haptic feedback
* changed eeprom to 32 bits to reserve blocks for future features
* start documentation of haptic feedback
* change keycode per comment from reviewers
* typo fixes
* added eeprom for solenoid configs
* added solenoid and docs
* Add/fix default parameters configs, improve docs
* more doc cleanup
* add in solenoid buzz toggle, clean up doc
* some fixes for error in compiling solenoid
* fix a chibios specific i2c read function and added one for AVR controllers in DRV2605L.c
* fixes for avr side issues
* update keymap
* fix keymap compile error
* fix bugs found during solenoid testing
* set pin that is not powered during bootloader
* added warning about certain pins on the MCU may trip solenoid during DFU/bootloader
* Add stm32f072 base ck4x4 to handwired
* add prints
* Save these tries
* Save changes again
* Working hadron oled
* OLEd working but ws2812b still iffy:
* save another try
* Encoder feature + OLED
* RTC code
* Implement clock setting mode
* Whitespace
* Encoder hooked up to working LED PWM code
* Add missing files
* eeprom changes
* Save changes
* Move i2c master
* Move satisfaction75 under cannonkeys
* Set proper default folder
* Revert some core changes
* Undo paved iris changes
* Reorganize code for maintainability and prep for new features
* Add starting code for clock OLED mode
* Clock set mode finished
* Add custom encoder modes
* Actually add VIA keymap
* Gate to only 072
* fix gate for only 072
* Update header guards and includes
* Update i2c selection strategy
* Update board.c to handle software reset to DFU
zvecr
Drashna Jaelre
fauxpark
Thomas Baart
yiancar
Yaotian Feng
MechMerlin
bwhelm
Mikkel Jeppesen
skullY
XScorpion2
Wilba
Michael F. Lamb
Nick Brassel
Jack Humbert
James Churchill
ishtob
Andrew Kannan