* Use memcmp and memcpy to compare and copy slave matrix.
...and memset to initialize `matrix` and `raw_matrix`.
Increased my scan rate (while connected) by ~100 (on Ergodox Infinity).
Effect on AVR is unknown.
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Fix `matrix_post_scan` signalling change on every scan while disconnected.
* Undo removal of initialization of `slave_matrix`.
This has the effect of increasing my Ergodox Infinity firmware size by 8
bytes instead of decreasing by 8 bytes, and lowers the scan rate while
connected back to the initial value before these changes, but _might_
solve some issues on AVR.
Co-authored-by: Stefan Kerkmann <karlk90@pm.me>
* Make solo half of split keyboards (more) usable.
Using only one half of a split keyboard (that's using the split_common
framework to communicate) is not a great experience, since several read
timeouts per scan cycle cause an unusably slow scan rate.
This change blocks all split communication attempts for 500 ms
(configurable) after an error occurs, causing the scan rate to become at
least _more_ usable, but might need some tweaking to work fully on most
keyboards. One read timeout still needs to occur after the 500 ms has
passed, and if that timeout isn't low enough, some scan cycles may still
be too slow.
* Fix lint complaint.
* Require 25 consecutive comm errors to see comms as disconnected.
The number of max errors can be overridden by defining
`SPLIT_MAX_CONNECTION_ERRORS`.
* Add comments to new defines, and ability to disable disconnection check.
Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible
by most relevant numbers for the description.
* Make lint happy ...again
* Only update `connection_check_timer` when needed.
* Add new defines to split keyboard documentation.
* Move connection timeout logic to transport.c, add `is_transport_connected`.
* Use split_common disconnection logic in matrix.c.
Instead of doing more or less the same thing twice.
* Move disconnection logic to `transport_master`.
Is a cleaner implementation, and causes the scan rate while disconnected
to increase instead of decrease.
* Lint fixes.
* Lower default `SERIAL_USART_TIMEOUT` to 20 ms.
The read timeout must be low enough to not cause exessively long scan
cycles when using a solo split half. 10 ms was determined from testing
to work fine even with the slowest defined baudrate of 19200 (5 ms was
too low for that case), so 20 ms should be fine for most cases.
* Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h
Was somewhat mistakenly included in an earlier PR.
* Fix building with `USE_I2C`.
* Reduce built firmware size.
Not really sure why this works, the idea was taken from tzarc's work on
split disconnection.
* Tweak and improve opt-out for split disconnection logic.
There are now two ways to opt out from this feature:
* Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable
the connection status checks (also affects the slave matrix reset logic in
matrix.c, though).
* Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the
communication throttling while disconnected. Will make the firmware
smaller.
* Make split disconnection logic work with custom transports.
Includes a fallback implementation for keyboards using a custom
split_util.c but not a custom matrix.c (currently no such keyboard seems
to be merged, though).
* Remove unnecessary include of timer.h
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
The prototype of matrix_output_unselect_delay() has been changed as follows.
```c
void matrix_output_unselect_delay(uint8_t line, bool key_pressed);
```
Currently, no keyboard seems to be redefining `matrix_output_unselect_delay()`, so there is no change in the system behavior.
With this change, the keyboard level code can get some optimization hints, for example, the following.
```c
void matrix_output_unselect_delay(uint8_t line, bool key_pressed) {
/* If none of the keys are pressed,
* there is no need to wait for time for the next line. */
if (key_pressed) {
#ifdef MATRIX_IO_DELAY
# if MATRIX_IO_DELAY > 0
wait_us(MATRIX_IO_DELAY);
# endif
#else
wait_us(30);
#endif
}
}
```
Two occurrences of `MATRIX_ROWS` weren't properly changed to
`ROWS_PER_HAND` in #13330, causing a crash during boot on at least my
Ergodox Infinity (including #13481).
* Use memcmp to determine if matrix changed.
* Firmware size issues.
* Add documentation for the lack of need of MATRIX_ROW_PINS/MATRIX_COL_PINS, when overriding low-level matrix functions.
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* fix matrix_io_delay() timing in quantum/matrix.c
* Updated comments explaining the need for matrix_io_delay() in quantum/matrix.c
* fix matrix_io_delay() timing in quantum/split_common/matrix.c
* Update quantum/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/split_common/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update quantum/split_common/matrix.c
Co-authored-by: Ryan <fauxpark@gmail.com>
* add waitOutputPinValid() and wait_cpuclock() into quantum/quantum.h and tmk_core/common/wait.h
* add matrix_output_select_delay() and matrix_output_unselect_delay()
* fix quantum/matrix_common.c, tmk_core/common/matrix.h
* fix tmk_core/common/wait.h
* fix quantum/quantum.h, tmk_core/common/wait.h
* waitOutputPinValid() rename to waitInputPinDelay() in quantum/quantum.h.
* waitOutputPinValid() rename to waitInputPinDelay() in quantum/matrix_common.c
* update tmk_core/common/wait.h
* update comment in quantum/matrix.c, quantum/split_common/matrix.c
* update quantum/quantum.h: Make more margin in the GPIO_INPUT_PIN_DELAY default value.
Co-authored-by: Ryan <fauxpark@gmail.com>
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* Enforce definition of `DIODE_DIRECTION` for non-custom matrix boards
* Define diode direction for failing boards
* Matching parentheses
* Put onekey diode directions in top level config
* Move some common matrix code to a common location
* Refactor some 'custom_matrix_helper' logic to use custom matrix lite
* Fix build for kinesis/stapelberg - abuse of vpath was picking up matrix.c from core when custom matrix was enabled
* Add validation for CUSTOM_MATRIX
* Port DIRECT_PINS from split_common/matrix.c to matrix.c
* Reorder matrix.c to remove foward declaration and match split_common/matrix.c
* Refactor nano to use DIRECT_PINS
* Reorder matrix.c to remove foward declaration and match split_common/matrix.c
* Add DIRECT_PINS documentation
* Reorder matrix.c to remove foward declaration and match split_common/matrix.c - fix logic from inherited from split_common
* Add DIRECT_PINS documentation - review comments
* Added xeal60 via clone of lets split
* Delete removed other keymaps
* Basic keymap (no FN). Compiles.
* Removed NP_STAR and NP_SLSH.
* Removed "debounce_algo = manual" in all keyboards with CUSTOM_MATRIX = yes.
* Changed order of rules in TMK. Documented feature.
* Fixed missing whitespace in debounce documentation
Table wasn't working due to missing newline.
* Added bold in a few areas.
* DO NOT USE - Removed debounce from TMK.
* Remove accidental xeal60 commit
* DO NOT USE - debounce successfully compiled.
* DO NOT USE Revert back to original API to support split_keyboards.
* Working eager_pk
* Whitespace cleanup.
* Restored debounce.h since there wasnt any real change.
* Moved debouncing_time variable to inside #if debounce
* Removed check for custom_matrix. We can safely include the debounce file for compilation when custom_matrix is used.
* Removed #include "matrix.h" from debounce.h
* Bug fix - was using MATRIX_ROWS instead of num_rows
* Fixed compilation error with debounce_sym_g
* Renamed DEBOUNCE_ALGO to DEBOUNCE_TYPE
* Malloc array in debounce_eager_pk, since split keyboards only use MATRIX_ROWS/2.
* Fix compile error in debounce_eager_pk
* Stricter, leaner DEBOUNCE_TYPE section in common_features.mk. Cleanup debounce_type.mk
* Eliminate separate slave loop
Both master and slave run the standard keyboard_task main loop now.
* Refactor i2c/serial specific code
Simplify some of the preprocessor mess by using common function names.
* Fix missing #endif
* Move direct pin mapping support from miniaxe to split_common
For boards with more pins than sense--sorry, switches.
* Reordering and reformatting only
* Don't run matrix_scan_quantum on slave side
* Clean up the offset/slaveOffset calculations
* Cut undebounced matrix size in half
* Refactor debouncing
* Minor fixups
* Split split_common transport and debounce code into their own files
Can now be replaced with custom versions per keyboard using
CUSTOM_TRANSPORT = yes and CUSTOM_DEBOUNCE = yes
* Refactor debounce for non-split keyboards too
* Update handwired/xealous to build using new split_common
* Fix debounce breaking basic test
* Dodgy method to allow a split kb to only include one of i2c/serial
SPLIT_TRANSPORT = serial or SPLIT_TRANSPORT = i2c will include only
that driver code in the binary.
SPLIT_TRANSPORT = custom (or anything else) will include neither, the
keyboard must supply it's own code
if SPLIT_TRANSPORT is not defined then the original behaviour (include
both avr i2c and serial code) is maintained.
This could be better but it would require explicitly updating all the
existing split keyboards.
* Enable LTO to get lets_split/sockets under the line
* Add docs for SPLIT_TRANSPORT, CUSTOM_MATRIX, CUSTOM_DEBOUNCE
* Remove avr-specific sei() from split matrix_setup
Not needed now that slave doesn't have a separate main loop.
Both sides (on avr) call sei() in lufa's main() after exiting
keyboard_setup().
* Fix QUANTUM_LIB_SRC references and simplify SPLIT_TRANSPORT.
* Add comments and fix formatting.
* Update quantum matrix to support both AVR and Chibios ARM
- Addition of STM32 pin definitions
- Created abstruction layer defines to control GPIO (This is a bit pointless for Chibios as we are creating a PAL ontop of a PAL but it is necessary for uniformity with AVR)
- Modified matrix.c to use the above functions
* minor ifdef fix
* Rename of functions and docs
- Added documentation.
- Renamed functions according to Jack's spec.
* Massdrop fix
* Update matrix.c
* Update quantum.h
* Update quantum.h
* Update quantum.h
* Update internals_gpio_control.md
* Clarify the license for files we have signoff on
* Update against the currently signed off files
* Remove unused and not clearly licensed headers
* Replace an #endif I accidentally removed while resolving merge conflicts
The previous two options were COL2ROW, ROW2COL; this adds CUSTOM_MATRIX
to disable the built-in matrix scanning code.
Most notably, this obviates the need to set MATRIX_ROW_PINS or
MATRIX_COL_PINS.
* Modularity and gcc warnings fixes.
* Add ChibiOS support (USB stack + support files).
* Make usb_main more USB_DRIVER #define independent.
* Move chibios to tool.
* Implement jump-to-bootloader.
* Small updates.
* Fix bootloader-jump compiling.
* Move AVR specific sleep_led.c into avr.
* Add basic sleep_led for chibios.
* Update chibios README.
* NKRO fixes.
* Rename some Makefile defines.
* Move STM32 bootloader address config to separate .h file.
* Add ARM Teensies bootloader code.
* Fix chibios/usb_main GET_REPORT handing.
* Add missing #include to keymap.c.
* Make bootmagic.c code portable (_delay_ms -> wait_ms).
* Move declaration of keymap_config.
Should really not declare variables in .h files - since it's included
in different .c files, a proper linker then complains that the same
variable is declared more than once (once for each .c file that the
offending .h is included in).
* Add eeprom support for chibios/kinetis.
* Rename chibios example keyboard.
* Move chibios/cortex selection to local Makefiles.
* Chibios: use WFI in idle. WIP suspend stuff.
* ChibiOS/kinetis: sending remote wakeup.
* ChibiOS/STM32: send remote wakeup.
* Fix report size of boot protocol.
* Fix drop key stroke
Keyboard report should be checked if its transfer finishs successfully.
Otherwise key stroke can be missing when other key event occurs
before the last report transfer is done.
Boot protocol 10ms interval probably causes this problem in case
it receives key events in a row within the period. NKRO protocol
suffers less or nothing due to its interval 1ms.
* Chibios/usb_main: rename a variable for clarity.
* Add correct chibios/bootloader_jump for infinity KB.
* ChibiOS: make reset request more CMSISy.
* Chibios: Add breathing sleep LED on Kinetis MCUs.
* ChibiOS: Update infinity bootloader code to match updated ChibiOS.
* ChibiOS: prettify/document sleep_led code.
* Chibios: Remove the wait in the main loop.
* Add maple mini code.
* Do timeout when writing to CONSOLE EP queue.
Fixes TMK bug #266.
* Chibios: add 'core/protocol' to the makefiles' search path.
* Chibios: Update to new USB API.
* Chibios: add more guards for transmitting (fix a deadlock bug).
* Add update for chibios in README
* Chibios: Fix a HardFault bug (wait after start).
* Chibios: cleanup usb_main code.
* Chibios: Revert common.mk change (fix AVR linking problem).
* core: Fix chibios user compile options
Compile options can be defined in project Makefile such as UDEFS, UADEFS, UINCDIR, ULIBDIR and ULIBS.
* Sysv format for ChibiOS arm-none-eabi-size
Some new patches to ChibiOS puts heap as it's own section. So the
berkeley format is now useless, as the heap will be included in the
BSS report. The sysv format displays the bss size correctly.
* Fix hard-coded path of CHIBIOS
* Add support for new version of ChibiOS and Contrib
The Kinetis support has moved to a separate Contrib repository in
the newest version of Chibios. There has also been some structure
changes. So this adds support for those, while maintaining back-
wards compability.
* Update ChibiOS instructions
* Chibios: implement sleep LED for STM32.
* Chibios: Update the main chibios README.
* Chibios: fix STM32_BOOTLOADER_ADDRESS name.
* Chibios: make the default bootloader_jump redefinable (weak).
* Chibios: disable LTO (link-time optimisation).
With LTO enabled, sometimes things fail for mysterious reasons
(e.g. bootloader jump on WF with LEDs enabled), just because the
linker optimisation is too aggressive.
* Chibios: add default location for chibios-contrib.
* ChibiOS: update mk to match chibios/master.
* ChibiOS: update instructions.md.
* Add chibi_onekey example.
* Add comments to chibi_onekey Makefile.
* Rename some Makefile defines.
* Move STM32 bootloader address config to separate .h file.
* Rename chibios example keyboard.
* Move chibios/cortex selection to local Makefiles.
* Add Teensy LC onekey example.
* Chibios: use WFI in idle. WIP suspend stuff.
* Update chibi/teensy instructions.
* Update chibios/Teensy instructions.
* Add infinity_chibios
* Add keymap_hasu.c
* Infinity_chibios: select correct bootloader_jump.
* Infinity_chibios: improve comments.
* Add generic STM32F103C8T6 example.
* Add maple mini code.
* STM32F103x fixes.
* Add maple mini pinout pic.
* Chibios: updates for 3.0.4 git.
* Chibios: rename example stm32_onekey -> stm32_f072_onekey.
* Chibios: add makefiles for Teensy 3.x examples.
* Chibios: update Teensy 3.x instructions.
* Chibios: Tsy LC is cortex-m0plus.
* Chibios: add more guards for transmitting (fix a deadlock bug).
* Change README for chibios
* Chibios: update examples to current chibios git.
Match the changes in mainline chibios:
- update chconf.h
- update supplied ld scripts structure
- update Teensy instructions (switch to official
chibios and introduce contrib)
* Add ChibiOS and ChibiOS-Contrib submodules
Also fix the makefile path for them.
* Moves chibios keyboards to keyboards folder
* First version of ChibiOS compilation
Only the stm32_f072_onkey keyboard is ported at the moment. It
compiles, but still doesn't link.
* More chibios fixes
It now compiles without warnings and links
* Move the teensy_lc_onekey to the keyboards folder
* Clean up the make file rule structure
* Remove keymap_fn_to_action
* Update more ChibiOS keyboards to QMK
Most of them does not compile at the moment though.
* Use older version of Chibios libraries
The newest ones have problems with compilation
* Remove USB_UNCONFIGURED event
It isn't present in the older version of ChibiOS
* Fix the infinity_chibios compilation
* Fix potentially uninitialized variable
* Add missing include
* Fix the ChibiOS makefile
* Fix some Chibios keyboard compilation
* Revert the rules.mk file back to master version
* Combine the chibios and AVR makefiles
With just the required overrides in the respective platform
specific one.
* Slight makefile restrucuring
Platform specific compiler options
* Move avr specific targets out of the main rules
* Fix ChibiOS objcopy
The ChibiOS objcopy needs different parameters, so the parameters
are moved to the corresponding platform rule file
* Fix the objcopy for real this time
The comands were moved around, so chibios used avr and the ohter
way around.
Also change the objsize output format
* Fix the thumb flags
* Fix the infinity hasu keymap
* Per platform cpp flags
* Add gcc-arm-none-eabi package to travis
* Add arm-none-eabi-newlib to travis
* Fix the name of the libnewlib-arm-none-eabi lib
* Fix the ChibiOS paths
So that they are properly relative, and builds don't generate
extra folders
* Fix the board path of stm32_f103_onekey
* Only consider folders with Makefiles as subproject
* non-working commit
* working
* subprojects implemented for planck
* pass a subproject variable through to c
* consolidates clueboard revisions
* thanks for letting me know about conflicts..
* turn off audio for yang's
* corrects starting paths for subprojects
* messing around with travis
* semicolon
* travis script
* travis script
* script for travis
* correct directory (probably), amend files to commit
* remove origin before adding
* git pull, correct syntax
* git checkout
* git pull origin branch
* where are we?
* where are we?
* merging
* force things to happen
* adds commit message, adds add
* rebase, no commit message
* rebase branch
* idk!
* try just pull
* fetch - merge
* specify repo branch
* checkout
* goddammit
* merge? idk
* pls
* after all
* don't split up keyboards
* syntax
* adds quick for all-keyboards
* trying out new script
* script update
* lowercase
* all keyboards
* stop replacing compiled.hex automatically
* adds if statement
* skip automated build branches
* forces push to automated build branch
* throw an add in there
* upstream?
* adds AUTOGEN
* ignore all .hex files again
* testing out new repo
* global ident
* generate script, keyboard_keymap.hex
* skip generation for now, print pandoc info, submodule update
* try trusty
* and sudo
* try generate
* updates subprojects to keyboards
* no idea
* updates to keyboards
* cleans up clueboard stuff
* setup to use local readme
* updates cluepad, planck experimental
* remove extra led.c [ci skip]
* disable power up for now
* config files updates
* makefile updates
* .h file updates, config tuning
* disable audio for yang
Joakim Tufvegren
Joakim Tufvegren
Takeshi ISHII
Drashna Jaelre
Nick Brassel
Michael Stapelberg
Ryan
James Young
QMK Bot
Joel Challis
skullY
Ryan Caltabiano
James Churchill
alex-ong
yiancar
Alex Ong
skullydazed
Nikolaus Wittenstein
Jack Humbert
IBNobody
IBNobody
fredizzimo
Eric Tang