ebb512db82
* Clean up `DEBOUNCE` in config.h, 0-9 * Clean up `DEBOUNCE` in config.h, A * Clean up `DEBOUNCE` in config.h, B * Clean up `DEBOUNCE` in config.h, C * Clean up `DEBOUNCE` in config.h, D * Clean up `DEBOUNCE` in config.h, E * Clean up `DEBOUNCE` in config.h, F * Clean up `DEBOUNCE` in config.h, G * Clean up `DEBOUNCE` in config.h, H * Clean up `DEBOUNCE` in config.h, handwired * Clean up `DEBOUNCE` in config.h, I * Clean up `DEBOUNCE` in config.h, J * Clean up `DEBOUNCE` in config.h, K * Clean up `DEBOUNCE` in config.h, L * Clean up `DEBOUNCE` in config.h, M * Clean up `DEBOUNCE` in config.h, N * Clean up `DEBOUNCE` in config.h, O * Clean up `DEBOUNCE` in config.h, P * Clean up `DEBOUNCE` in config.h, Q * Clean up `DEBOUNCE` in config.h, R * Clean up `DEBOUNCE` in config.h, S * Clean up `DEBOUNCE` in config.h, T * Clean up `DEBOUNCE` in config.h, U * Clean up `DEBOUNCE` in config.h, V * Clean up `DEBOUNCE` in config.h, W * Clean up `DEBOUNCE` in config.h, X * Clean up `DEBOUNCE` in config.h, Y * Clean up `DEBOUNCE` in config.h, Z * Remove default debounce from info.json * Migrate non-default debounce to info.json |
||
|---|---|---|
| .. | ||
| keymaps/default | ||
| config.h | ||
| info.json | ||
| launch_1.c | ||
| launch_1.h | ||
| post_rules.mk | ||
| readme.md | ||
| rgb_matrix_kb.inc | ||
| rules.mk | ||
| usb_mux.c | ||
| usb_mux.h | ||
readme.md
System76 Launch Configurable Keyboard (launch_1)
The Launch Configurable Keyboard is engineered to be comfortable, fully customizable, and make your workflow more efficient.
- High-speed USB Hub
- Works on Linux, Windows and macOS
- 100% Open Source
- Made in Colorado
Additional Launch Keyboard resources:
- Keyboard Maintainer: System76
- Hardware Supported: System76 Launch GitHub Repository
- Hardware Availability: Shop System76
Building Firmware
To build the firmware using make (after setting up the build environment), e.g.:
make -r system76/launch_1:default
Equivalently, using the QMK CLI:
qmk compile -kb system76/launch_1 -km default
Flashing Firmware (DFU)
To build and flash the firmware on the keyboard, e.g.:
make -r system76/launch_1:default:flash
Equivalently, using the QMK CLI:
qmk flash -kb system76/launch_1 -km default
Flashing Firmware (ISP)
To flash the firmware (and/or bootloader) using ISP refer to the ISP Flashing Guide.
Factory fuse values => Low:
0x5E, High:0x99, Extended:0xF3, Lock Bits:0xFF
Environment Setup
See the build environment setup and the make instructions for more information. If new to QMK, start with the Complete Newbs Guide.
Bootloader
Enter the bootloader in 3 ways:
- Bootmagic reset: Hold down the key at (0,0) in the matrix (Escape) and plug in the keyboard.
- Keycode in layout: Press the key mapped to
QK_BOOTin the second layer (Escape). - Electrical reset: Briefly short AVR ISP's GND (6) and RST (5) pads on the back of the PCB.