Alternative Controller for HHKB
===============================
Feature
-------
- Mouse Keys
- NKRO on USB(PJRC Tennsy only)
- Keymap Layers
Customize Keymap
----------------
see keymap.c.
Build
=====
PJRC Teensy
-----------
0. Edit matrix.c.
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
1. Define macros in config_pjrc.h.(Optional)
VENDOR_ID, PRODUCT_ID and string descriptor.
IS_COMMAND
2. Edit Makefile for MCU setting and build options.
MCU, F_CPU
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE, NKRO_ENABLE
3. Build hex file.
$ make -f Makefile.pjrc
4. Program MCU.
$ make -f Makefile.pjrc program
V-USB
-----
0. Edit matrix.c and usbconfig.h.
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
define macros for V-USB in usbconfig.h.
1. Define macros in config_vusb.h.(Optional)
IS_COMMAND
2. Edit Makefile.vusb for MCU setting and build options.
MCU, F_CPU
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
3. Build hex file.
$ make -f Makefile.vusb
4. Program MCU.
$ make -f Makefile.vusb program
Using a bootloader to program for convenience is recommended.
Once program this V-USB bootloader at first, you can program MCU without
extra programmer. You should have reset switch to start up as bootloader
mode in this case.
USBaspLoader:
http://www.obdev.at/products/vusb/usbasploader.html
iWRAP
-----
0. Edit matrix.c and usbconfig.h.
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
define macros for V-USB in usbconfig.h.
1. Define macros in config_iwrap.h.(Optional)
IS_COMMAND
2. Edit Makefile.iwrap for MCU setting and build options.
MCU, F_CPU
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
3. Build hex file.
$ make -f Makefile.iwrap
4. Program MCU.
$ make -f Makefile.iwrap program
Hardware
========
PJRC Teensy
-----------
+---------------+
| Teensy++ |
| |
| | HHKB
| | ~~~~
| PB0-2|------->ROW(6-8)
| PB3-5|------->COL(9-11)
| PB6|------->ENABLE(12)
| PE6|<-------KEY(4)
| PE7|------->PREV(5)
| |
| |
| |
+---------------+
V-USB
-----
+---+ +---------------+
USB GND | | ATmega168 |
~~~ C3 | |
5V <-------+--------+---|Vcc,AVCC | HHKB
R1 | | ~~~~
D- <----+--+-----R2-----|INT1 PB2-4|------->ROW(6-8)
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
Z1 Z2 | PC3|------->ENABLE(12)
GND<----+---+-----------|GND PB0|<-------KEY(4)
| PB1|------->PREV(5)
| |
GND+-C2--+--|XTAL1 RXD|------->Debug Console
X1 | TXD|<-------Debug Console
GND+-C3--+--|XTAL2 RST|---SW--+GND
+---------------+
R1: 1.5K Ohm
R2,R3: 68 Ohm
Z1,Z2: Zener 3.6V
C1,C2: 22pF
C3: 0.1uF
X1: Crystal 20MHz(16MHz/12MHz)
SW: Push Switch(Optional for bootloader)
iWRAP
-----
+---------------+ WT12
5V | ATmega168 | 5V/3.3V~~~~
+-----+---|Vcc,AVCC PC4|---/--->iWRAP(RxD)
USB | C3 | PC5|<--/----iWRAP(TxD)
~~~ | + | |
5V <--BATT + GND | | HHKB
R1 | | ~~~~
D- <----+-----+--R2-----|INT1 PB2-4|------->ROW(6-8)
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
Z1 Z2 | PC3|------->ENABLE(12)
GND<----+---+-----------|GND PB0|<-------KEY(4)
| PB1|------->PREV(5)
| |
GND+-C2--+--|XTAL1 RXD|------->Debug Console
X1 | TXD|<-------Debug Console
GND+-C3--+--|XTAL2 RST|---SW--+GND
+---------------+
R1: 1.5K Ohm
R2,R3: 68 Ohm
Z1,Z2: Zener 3.6V
C1,C2: 22pF
C3: 0.1uF
X1: Crystal 12MHz
SW: Push Switch(Optional)
BATT: Li-Po Battery, Battery Charger and Voltage Regulator(5V and 3.3V).
EOF
fe71523443