* Remove unnecessary IS_COMMAND definition in clueboard/66/rev4
* Replace keyboard_report->mods with get_mods() in IS_COMMAND definitions
* Update docs to use get_mods() instead of keyboard_report->mods
* Replace keyboard_report->mods with get_mods() in tmk_core/protocol/usb_hid/test
For some reason, this occurrence used KB_LSHIFT and KB_RSHIFT, which don't exist
* Replace keyboard_report->mods with get_mods() in Massdrop keyboards (as per @patrickmt)
* Add default value for IS_COMMAND for COMMAND feature
* Cleanup and consistency
* Update Templates to reflect change
* Fix IS_COMMAND in template
* Fix IS_COMMAND define
* Use consistent IS_COMMAND block in templates
* Remove unnecessary `#undef IS_COMMAND` directives
* Fix compile issue on orthodox
* Reomve IS_COMMAND option for newer boards
* Remove all existing definitions of IS_COMMAND if they use default LSHIFT and RSHIFT setting
* Remove a couple of additional IS_COMMAND defines
* Remove remaining redundant IS_COMMAND definitions
* Remove #undef IS_COMMAND from orthodox:drashna and whitefox:konstantin
* Remove multiple empty lines in modified config.h files
* Update additional boards
* Reomve IS_COMMAND from newer boards
* Update Alice keyboard
* Remove IS_COMMAND from additional boards
Jan 24th edition
Microsecond (us) delays are now handled by a busy wait loop according to MCU frequency. This replaces the system counter method which had an overhead of around 12us.
TC5 device and supporting routines removed as it was the old us delay counter.
wait_ms is now properly a macro to CLK_delay_ms.
wait_us is now properly a macro to CLK_delay_us.
Removed CLK_get_us as it has no use.
All calls to CLK_get_ms() have been replaced by timer_read64() with corrected typing.
All calls to CLK_delay_ms() have been replaced by wait_ms().
All calls to CLK_delay_us() have been replaced by wait_us() and timings verified or updated as needed after review on scope.
Corrected typing of variables using 64bit ms timer readings if needed.
MCU Pins for debugging, LED, boot tracing, and shift registers are now configurable at keyboard level.
Macros led_* replaced by DBG_LED_*
Macros m15_* replaced by DBG_1_*
Macros m27_* replaced by DBG_2_*
Macros m28_* replaced by DBG_3_*
For CTRL and ALT keyboards, debug boot tracing pin default now set to pad M27 instead of M28 since although M28 is not being used, it is technically a signal for USB port detection.
m15_print(...) renamed to dbg_print(...) to get away from hard coded port names.
dbg_print function now follows similar pattern to debug led output.
* Update for SEND_STRING usage
Update for SEND_STRING usage.
Sending keyboard reports (kbd, nkro) now obey the minimum polling time.
While attempting to send a keyboard report and waiting for a USB poll, other functions of the keyboard, including LED effects and power management, will continue to operate at their intended intervals.
* Updates for send string, syscalls, stdio, debug prints, auto shift
Now properly waiting for previous keys sent over USB to complete before sending new.
Added heap to linker and now compiling with syscalls support.
Removed custom string functions and now using stdio.
dprintf now works as intended through virtser device.
* CTRL and ALT keymap updates
CTRL mac keymap updated
ALT default and mac keymap updated
ALT rules.mk added Auto Shift with default no
* Code cleanup as per discussion with vomindoraan
Code cleanup as per discussion with vomindoraan
* ALT keymap update
Added additional End key on layer 1 to match key cap
* LED driver update addressing PR #3871
Update sync between IS31FL3733 drivers is causing varying behavior in keyboards including brightness mismatch and slight flicker at very low rgb values. Visually, disabling sync is not noticeable. Ref PR #3871 by guarnacciaa.
Added support to enter bootloader from software (bootloader version must be newer than "v2.18Jun 22 2018 17:28:08" until workaround for older is created).
Updated CTRL and ALT keymaps for entering bootloader with Fn+b held for >500ms.
Added basic MacOS keymap for ALT.
USB sleep LED indicator now turns off after 1 second.
Slowed down debug LED code printing.
Renamed keyboard alt67 to alt and adjusted necessary files where alt67 appeared.
CTRL keymap fixed enum structure name.
usb2422 removed stray define no longer used.
Konstantin Đorđević
Drashna Jaelre
fauxpark
patrickmt
abishalom
Sean Dwyer