* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
* redo make args to use colons, better folder structuring system [skip ci]
* don't put spaces after statements - hard lessons in makefile development
* fix-up some other rules.mk
* give travis a chance
* reset KEYMAPS variable
* start converting keyboards to new system
* try making all with travis
* redo make args to use colons, better folder structuring system [skip ci]
* don't put spaces after statements - hard lessons in makefile development
* fix-up some other rules.mk
* give travis a chance
* reset KEYMAPS variable
* start converting keyboards to new system
* try making all with travis
* start to update readmes and keyboards
* look in keyboard directories for board.mk
* update visualizer rules
* fix up some other keyboards/keymaps
* fix arm board ld includes
* fix board rules
* fix up remaining keyboards
* reset layout variable
* reset keyboard_layouts
* fix remainging keymaps/boards
* update readmes, docs
* add note to makefile error
* update readmes
* remove planck keymap warnings
* update references and docs
* test out tarvis build stages
* don't use stages for now
* don't use stages for now
* Added orthodox
* Modified readme
* Modified readme
* Modified readme
* Updated makefile
* Fixed keymap issues
* Modified serial communications to allow for over 8 columns
* Fixed sizeof command
* Fixed some typing issues
* Testing issue #1191 (n-column split i2c slave)
Based on initial OrthoDox (serial) config by @reddragond and others,
this attempts to add TWI (I2C) support.
Relevant: <https://github.com/qmk/qmk_firmware/issues/1191>
- per @ahtn recommendation, using memcpy for moving slave matrix
into slave sending buffer
- slave buffer has been enlarged using sizeof(matrix_row_t)
- note: i2c.h now includes matrix.h
- note: matrix.c includes <string.h>
* Added i2c keymap - right col still not working
* orthodox: re-added i2c keymap, based on serial
* orthodox / issue #1191: trying 9-bit serial
- orthodox serial protocol now sends 9 bits per row, instead of 16.
Technically it's using MATRIX_COLS, so it might work generically.
- ROW_MASK is #defined in serial.c to truncate the checksums to prevent
overflows causing false errors. This macro should be renamed if it's
kept.
* Revert "Fixed sizeof command"
This reverts commit f62a5b9939d6a9c0e442ec403de00c14431a55f9.
Changes had been made to the lets_split serial driver for testing which
mirrored the multi-byte-row changes made to support the orthodox. As the
lets_split does not require these changes, and new improvements had
been added to the orthodox port only, this commit reverts them.
Because the new code could potentially reduce latency over the serial
transport, it may be desirable to re-add in the future, by backporting
the current working orthodox code.
* orthodox: default serial keymap improvements
- formatting has been improved
- a few keys have been shifted, mainly in Raise and Lower layers,
to be more like the default Planck layout
- Now available: F12, Home, End, PgUp, PgDn, Media-Next, Media-Play
Still To Do:
- duplicate for TWI
- Alt modifier
- GUI modifier
* orthodox: failed attempt at 16b/row TWI
- duplicated updated serial keymap for "i2c"
- removed string.h/memcpy, instead
- hardcoded copying of six bytes per update
- still doesn't work; master reports interconnect errors on txled
* orthodox: adjusted default keymap
- this is applied to both 'serial' and 'i2c' keymaps
- Alt and GUI have been added, as they were missing
- comma and period persist across more layers; Home/PgUp and End/PgDn
have been moved slightly to accommodate
* orthodox: revert TWI support to minimum to debug
- disabled ssd1306 and hardware locking in build configuration
- increased TWI buffer from 0x10 to 0x20 bytes
- decreased TWI clock from 400000 to 100000
- removed hardcoded TWI multi-byte sending/receiving
An 'i2c' build of this was found to work on a rev1 Orthodox, although
slave-side col9 was understandably not working. When testing-time
permits, features will be gradually re-enabled towards getting the full
matrix supported over TWI.
* orthodox: TWI (i2c) is working, kludge for col9
The TWI interconnect ("i2c" in directories and build config) is now
working for the Orthodox, including the slave half's column #9.
This is intended as an interim solution, as it's a kludge, not a fix.
Rather than a working multi-byte implementation, the two col9 keys'
bits are packed-into and unpacked-from the two unused bits in row1.
Furthermore, the TWI clock constant has been reduced to 100000 from
400000, as testing revealed the higher value just didn't work.
Testing also found that (with this kludge) increasing the TWI buffer
was not necessary.
This commit leaves many commented-out lines in matrix.c from previous
testing, which will be removed in a future commit once the
interconnects' multi-byte problems have been debugged more thoroughly.
* orthodox: updated readme.md
The readme for the Orthodox now includes a description of the keyboard,
allusions to its author and availability, a linked photo, and links to
the evolving build guide and the current keymap on KLE.
This update has been prepared with /u/Deductivemonkee's assistance.
James Young
Drashna Jaelre
Jack Humbert
Art Ortenburger