* disambiguate Bootmagic rules in keymaps
The files edited by this commit were added at a point in time where `BOOTMAGIC_ENABLE = yes` enabled full Bootmagic.
This commit edits the files to specify that full Bootmagic is intended.
* remove BOOTMAGIC_ENABLE=full setting
* unify commented BOOTMAGIC_ENABLE rules in keyboards
Explicitly sets `BOOTMAGIC_ENABLE = no` in keyboards where the rule was commented out.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;#[ \t]*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-zA-Z]\+\).*;\1 = no # Virtual DIP switch configuration;g' {} +
```
* remove commented Bootmagic rules from keymap/user level
Command:
```
find keyboards/ layouts/ users/ -type f -name 'rules.mk' -exec sed -i -e '/#.*\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*/d' {} +
```
* update keyboard BOOTMAGIC_ENABLE rule formatting
Sets the formatting of BOOTMAGIC_ENABLE rules to `BOOTMAGIC_ENABLE = [value]`, without the inline comments (which will be replaced later).
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
```
* update keyboards' BOOTMAGIC_ENABLE settings
Updates keyboard `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Command:
```
find keyboards/ -type f -name 'rules.mk' -and -not -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = \)full;\1lite;g' '{}' +
```
* update keymap/user BOOTMAGIC_ENABLE settings
Updates keymap/user `rules.mk` files to use `BOOTMAGIC_ENABLE = lite` where `BOOTMAGIC_ENABLE = full` was being used.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE[ \t=]\+\)full;\1lite;g' '{}' +
```
* remove and replace inline comments in keyboards and keymap/user files
Removes and replaces the inline comments, which have been updated to read `Enable Bootmagic Lite`.
Commands:
```
find keyboards/ -type f -name 'rules.mk' -and -path '*/keymaps/*' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE\)[ \t=]\+\([a-z]\+\).*;\1 = \2;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = lite\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = yes\);\1 # Enable Bootmagic Lite;g' '{}' +
find keyboards/ layouts/community/ users/ -type f -name 'rules.mk' -exec sed -i -e 's;\(BOOTMAGIC_ENABLE = no\);\1 # Enable Bootmagic Lite;g' '{}' +
```
* rename improperly named makefiles
Some files intended to be used as makefiles had improper names causing them to not be used as intended when building.
This commit corrects the filenames of the affected files.
* update renamed file with new rule formatting
* update QMK's template files
Updates QMK's `rules.mk` templates to use the new inline comment.
* update QMK Docs
- remove documentation of full Bootmagic
- update links to Bootmagic Lite doc
- add doc for Magic Keycodes
* rules.mk patch for coarse/ixora and coarse/vinta
* Add Per Key functionality for AutoShift (#11536)
* LED Matrix: Reactive effect buffers & advanced indicators (#12588)
* [Keyboard] kint36: switch to sym_eager_pk debouncing (#12626)
* [Keyboard] kint2pp: reduce input latency by ≈10ms (#12625)
* LED Matrix: Split (#12633)
* [CI] Format code according to conventions (#12650)
* feat: infinite timeout for leader key (#6580)
* feat: implement leader_no_timeout logic
* docs(leader_key): infinite leader timeout docs
* Format code according to conventions (#12680)
* Update ADC driver for STM32F1xx, STM32F3xx, STM32F4xx (#12403)
* Fix default ADC_RESOLUTION for ADCv3 (and ADCv4)
Recent ChibiOS update removed ADC_CFGR1_RES_10BIT from the ADCv3 headers
(that macro should not have been there, because ADCv3 has CFGR instead of
CFGR1). Fix the default value for ADC_RESOLUTION to use ADC_CFGR_RES_10BITS
if it is defined (that name is used for ADCv3 and ADCv4).
* Update ADC docs to match the actually used resolution
ADC driver for ChibiOS actually uses the 10-bit resolution by default
(probably to match AVR); fix the documentation accordingly. Also add
both ADC_CFGR_RES_10BITS and ADC_CFGR1_RES_10BIT constants (these names
differ according to the ADC implementation in the particular MCU).
* Fix pinToMux() for B12 and B13 on STM32F3xx
Testing on STM32F303CCT6 revealed that the ADC mux values for B12 and
B13 pins were wrong.
* Add support for all possible analog pins on STM32F1xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 on STM32F1xx
(they are the same at least for STM32F103x8 and larger F103 devices, and
also F102, F105, F107 families). Actually tested on STM32F103C8T6
(therefore pins C0...C5 were not tested).
Pins F6...F10, which are present on STM32F103x[C-G] in 144-pin packages,
cannot be supported at the moment, because those pins are connected only
to ADC3, but the ChibiOS ADC driver for STM32F1xx supports only ADC1.
* Add support for all possible analog pins on STM32F4xx
Added ADC mux values for pins A0...A7, B0, B1, C0...C5 and optionally
F3...F10 (if STM32_ADC_USE_ADC3 is enabled). These mux values are
apparently the same for all F4xx devices, except some smaller devices may
not have ADC3.
Actually tested on STM32F401CCU6, STM32F401CEU6, STM32F411CEU6 (using
various WeAct “Blackpill” boards); only pins A0...A7, B0, B1 were tested.
Pins F3...F10 are inside `#if STM32_ADC_USE_ADC3` because some devices
which don't have ADC3 also don't have the GPIOF port, therefore the code
which refers to Fx pins does not compile.
* Fix STM32F3xx ADC mux table in documentation
The ADC driver documentation had some errors in the mux table for STM32F3xx.
Fix this table to match the datasheet and the actual code (mux settings for
B12 and B13 were also tested on a real STM32F303CCT6 chip).
* Add STM32F1xx ADC pins to the documentation
* Add STM32F4xx ADC pins to the documentation
* Add initial support for tinyuf2 bootloader (when hosted on F411 blackpill) (#12600)
* Add support for jumping to tinyuf2 bootloader. Adds blackpill UF2 example.
* Update flashing.md
* Update chconf.h
* Update config.h
* Update halconf.h
* Update mcuconf.h
* eeprom driver: Refactor where eeprom driver initialisation (and EEPROM emulation initialisation) occurs to make it non-target-specific. (#12671)
* Add support for MCU = STM32F446 (#12619)
* Add support for MCU = STM32F446
* Update platforms/chibios/GENERIC_STM32_F446XE/configs/config.h
* Restore mcuconf.h to the one used by RT-STM32F446RE-NUCLEO64
* stm32f446: update mcuconf.h and board.h for 16MHz operation, with USB enabled, and other peripherals disabled.
* Format code according to conventions (#12682)
* Format code according to conventions (#12687)
* Add STM32L433 and L443 support (#12063)
* initial L433 commit
* change to XC
* fix L433
* disable all peripherals
* update system and peripheral clocks
* 433 change
* use its own board files
* revert its own board files
* l433 specific change
* fix stm32l432xx define
* remove duplicate #define
* fix bootloader jump
* move to L443xx and add i2c2, spi2, usart3 to mcuconf.h
* move to L443
* move to L443
* fix sdmmc in mcuconf.h
* include STM32L443
* add L443
* Include L443 in compatible microcontrollers
* Include L443 in compatible microcontrollers
* Update config bootloader jump description
* Update ChibiOS define reasoning
* Update quantum/mcu_selection.mk
* fix git conflict
* Updated Function96 with V2 files and removed chconf.h and halconf.h (#12613)
* Fix bad PR merge for #6580. (#12721)
* Change RGB/LED Matrix to use a simple define for USB suspend (#12697)
* [CI] Format code according to conventions (#12731)
* Fixing transport's led/rgb matrix suspend state logic (#12770)
* [CI] Format code according to conventions (#12772)
* Fix comment parsing (#12750)
* Added OLED fade out support (#12086)
* fix some references to bin/qmk that slipped in (#12832)
* Resolve a number of warnings in `qmk generate-api` (#12833)
* New command: qmk console (#12828)
* stash poc
* stash
* tidy up implementation
* Tidy up slightly for review
* Tidy up slightly for review
* Bodge environment to make tests pass
* Refactor away from asyncio due to windows issues
* Filter devices
* align vid/pid printing
* Add hidapi to the installers
* start preparing for multiple hid_listeners
* udev rules for hid_listen
* refactor to move closer to end state
* very basic implementation of the threaded model
* refactor how vid/pid/index are supplied and parsed
* windows improvements
* read the report directly when usage page isn't available
* add per-device colors, the choice to show names or numbers, and refactor
* add timestamps
* Add support for showing bootloaders
* tweak the color for bootloaders
* Align bootloader disconnect with connect color
* add support for showing all bootloaders
* fix the pyusb check
* tweaks
* fix exception
* hide a stack trace behind -v
* add --no-bootloaders option
* add documentation for qmk console
* Apply suggestions from code review
* pyformat
* clean up and flesh out KNOWN_BOOTLOADERS
* Remove pointless SERIAL_LINK_ENABLE rules (#12846)
* Make Swap Hands use PROGMEM (#12284)
This converts the array that the Swap Hands feature uses to use PROGMEM,
and to read from that array, as such. Since this array never changes at
runtime, there is no reason to keep it in memory. Especially for AVR
boards, as memory is a precious resource.
* Fix another bin/qmk reference (#12856)
* [Keymap] Turn OLED off on suspend in soundmonster keymap (#10419)
* Fixup build errors on `develop` branch. (#12723)
* LED Matrix: Effects! (#12651)
* Fix syntax error when compiling for ARM (#12866)
* Remove KEYMAP and LAYOUT_kc (#12160)
* alias KEYMAP to LAYOUT
* remove KEYMAP and LAYOUT_kc
* Add setup, clone, and env to the list of commands we allow even with broken modules (#12868)
* Rename `point_t` -> `led_point_t` (#12864)
* [Keyboard] updated a vendor name / fixed minor keymap issues (#12881)
* Add missing LED Matrix suspend code to suspend.c (#12878)
* LED Matrix: Documentation (#12685)
* Deprecate `send_unicode_hex_string()` (#12602)
* Fix spelling mistake regarding LED Matrix in split_common. (#12888)
* [Keymap] Fix QWERTY/DVORAK status output for kzar keymap (#12895)
* Use milc.subcommand.config instead of qmk.cli.config (#12915)
* Use milc.subcommand.config instead
* pyformat
* remove the config test
* Add function to allow repeated blinking of one layer (#12237)
* Implement function rgblight_blink_layer_repeat to allow repeated blinking of one layer at a time
* Update doc
* Rework rgblight blinking according to requested change
* optimize storage
* Fixup housekeeping from being invoked twice per loop. (#12933)
* matrix: wait for row signal to go HIGH for every row (#12945)
I noticed this discrepancy (last row of the matrix treated differently than the
others) when optimizing the input latency of my keyboard controller, see also
https://michael.stapelberg.ch/posts/2021-05-08-keyboard-input-latency-qmk-kinesis/
Before this commit, when tuning the delays I noticed ghost key presses when
pressing the F2 key, which is on the last row of the keyboard matrix: the
dead_grave key, which is on the first row of the keyboard matrix, would be
incorrectly detected as pressed.
After this commit, all keyboard matrix rows are interpreted correctly.
I suspect that my setup is more susceptible to this nuance than others because I
use GPIO_INPUT_PIN_DELAY=0 and hence don’t have another delay that might mask
the problem.
* ensure we do not conflict with existing keymap aliases (#12976)
* Add support for up to 4 IS31FL3733 drivers (#12342)
* Convert Encoder callbacks to be boolean functions (#12805)
* [Keyboard] Fix Terrazzo build failure (#12977)
* Do not hard set config in CPTC files (#11864)
* [Keyboard] Corne - Remove legacy revision support (#12226)
* [Keymap] Update to Drashna keymap and user code (based on develop) (#12936)
* Add Full-duplex serial driver for ARM boards (#9842)
* Document LED_MATRIX_FRAMEBUFFER_EFFECTS (#12987)
* Backlight: add defines for default level and breathing state (#12560)
* Add dire message about LUFA mass storage bootloader (#13014)
* [Keyboard] Remove redundant legacy and common headers for crkbd (#13023)
Was causing compiler errors on some systems.
* Fix keyboards/keymaps for boolean encoder callback changes (#12985)
* `backlight.c`: include `eeprom.h` (#13024)
* Add changelog for 2021-05-29 Breaking Changes merge (#12939)
* Add ChangeLog for 2021-05-29 Breaking Changes Merge: initial version
* Add recent develop changes
* Sort recent develop changes
* Remove sections for ChibiOS changes per tzarc
No ChibiOS changes this round.
* Add and sort recent develop changes
* add notes about keyboard moves/deletions
* import changelog for PR 12172
Documents the change to BOOTMAGIC_ENABLE.
* update section headings
* re-sort changelog
* add additional note regarding Bootmagic changes
* remove changelog timestamp
* update dates in main Breaking Changes docs
* fix broken section anchors in previous changelogs
* add link to backlight/eeprom patch to changelog
* highlight some more changes
* link PRs from section headers
* Restore standard readme
* run: qmk cformat --core-only
Co-Authored-By: Ryan <fauxpark@gmail.com>
Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-Authored-By: Drashna Jaelre <drashna@live.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Add backlight custom driver to all boards not declaring it but overriding backlight
* Apply suggestions from code review
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Apply suggestions from code review
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Remove old tmk references from show_options.mk
Co-authored-by: fauxpark <fauxpark@gmail.com>
* Removed reference to firmware size in 0-9,a-f board-level and default keymap 'rules.mk' files
* Correct some 'rules.mk' in boards buried under vendor folders
* PR8027 patch
Co-authored-by: GeorgeKoenig <35542036+GeorgeKoenig@users.noreply.github.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* add indicator lighting support thanks to Keebology tracing
* set the correct number of underglow LEDs
* add comments and skeletal structure for layer indicator LEDs
* add backlight areas pins
* update readme
* we can't turn leds on based on zones, so we use multiple backlight pin support instead to turn them ALL on and control them.
* add comments to backlight setting
* make a more useful default keymap that can also be used for testing
* add duck orion to list
* add indicator led support
* update readme
* Update keyboards/duck/orion/v3/matrix.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/duck/orion/v3/matrix.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/duck/orion/v3/matrix.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/duck/orion/v3/matrix.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/duck/orion/v3/matrix.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Update keyboards/duck/orion/v3/matrix.c
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* add the appropriate header files
* fix indent so Drashna will not die
* Update keyboards/duck/orion/v3/v3.c
Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com>
* Update keyboards/duck/orion/v3/keymaps/default/keymap.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/duck/orion/v3/keymaps/default/keymap.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/duck/orion/v3/readme.md
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/duck/orion/v3/readme.md
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/duck/orion/v3/readme.md
Co-Authored-By: fauxpark <fauxpark@gmail.com>
Co-authored-by: Drashna Jaelre <drashna@live.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: fauxpark <fauxpark@gmail.com>
* initial commit
* fixup init_rows and read_rows routine
* fixup matrix based on Marcus's tracing info
* add a temporary keymap
* add notes
* use a standard tkl ansi keymap
* turn on that last column
* backslash and backspace row left to fix
* reorg from backslash to pgdn
* got the matrix done but the backspace location at K4N is still suspect
* add reset info into readme
* add qmk configurator support
* add community layout support
* remove uneeded keymap readme
* add a new column just for the reset switch
* change copyright dates
* add cautionary message to readme as we don't know about the lighting condition yet
* Update keyboards/duck/orion/v3/v3.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/duck/orion/v3/v3.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* Update keyboards/duck/orion/v3/v3.c
Co-Authored-By: fauxpark <fauxpark@gmail.com>
* change bootloader comments
* Expand info.json formatting to one line per key
This is a white-space-only change. Make it easier for me to read the file.
* Make sure every key object has a label
Going to be using them shortly.
* Insert key identifiers from v1.h into info.json labels
Shows where each key is located in the switch matrix.
* Move K5O to its correct location on the top row
* Adjust white space in v1.h
At this point, the macros for LAYOUT and LAYOUT_75_ansi are 100% identical, except for their names.
* Redefine LAYOUT_75_ansi as an alias of LAYOUT
No need for two code blocks with the same data.
* Correct visual positioning in info.json
- move Pause 1u to the right
- move K5O to the top row, between Print Screen and Pause
- move Enter key 1u to the left and 1u wider (1.25u to 2.25u)
* Delete key identifiers from info.json labels
Don't need them anymore now that we know where everything is.
I'm calling K5O as ScrLk so it has a label, even though that's not actually what it is.
Also gave the Spacebar a label because I prefer when all the keys have labels.
* Enable 75_ansi Community Layout support
* Reassign layout macro as LAYOUT_75_ansi and delete macro alias
Configure the codebase so LAYOUT_75_ansi is the only layout macro available.
* Add key_count key to info.json data
* first [ass at pulling out common duck library functions
* use new library in jetfire
* use new library in duck lightsaver
* use new library in octagon v2
* put Device into the library
* refactor send_value
* refactor send_value and send_color
* use pragma once
* use pragma once
* use pragma once
* use pragma once
* rename backlight_led to indicator_leds to match with other duck boards
* rename enum
* make #define names consistent
* rename ducklib to duck_led
* update rules.mk ?= to =
* put rgb in the correct order
* add debounce debugging printouts
* turn on bootmagic lite and set it to the top left most key commonly programmed as Escape
* add reset key documentation
* fix that typo
* Update keyboards/duck/duck_led/duck_led.c
Co-Authored-By: mechmerlin <30334081+mechmerlin@users.noreply.github.com>
* include the correct library
* Add default value for IS_COMMAND for COMMAND feature
* Cleanup and consistency
* Update Templates to reflect change
* Fix IS_COMMAND in template
* Fix IS_COMMAND define
* Use consistent IS_COMMAND block in templates
* Remove unnecessary `#undef IS_COMMAND` directives
* Fix compile issue on orthodox
* Reomve IS_COMMAND option for newer boards
* Remove all existing definitions of IS_COMMAND if they use default LSHIFT and RSHIFT setting
* Remove a couple of additional IS_COMMAND defines
* Remove remaining redundant IS_COMMAND definitions
* Remove #undef IS_COMMAND from orthodox:drashna and whitefox:konstantin
* Remove multiple empty lines in modified config.h files
* Update additional boards
* Reomve IS_COMMAND from newer boards
* Update Alice keyboard
* Remove IS_COMMAND from additional boards
Jan 24th edition
* change VENDOR_ID, PRODUCT_ID, and DEVICE_VER as step one in getting VIA support
* fix v1 product id
* VIA doesn't use the version, so we need to encode it into PRODUCT_ID
* Updated info.json for Duck Jetfire
Generated a new info.json file. @mechmerlin asked my help in debugging this file. Firmware works as expected if built from source, but not if built from the Configurator.
* Corrected the position of the arrow keys in LAYOUT_all
* Move octagon directory into duck diretory and fix as many compile issues as I can
* fix formatting
* fix layout75 matrix
* edit readme for build instructions
* Initial Commit
Port from xauser's jetfire code. Does not compile yet
* fix up keymap from uint8 to uin16
* update rules file to contain custom matrix
* Good stopping point
Still lots of compile errors but I'm getting there.
* fix a few more compile errors
* move a few functions around to help with compiling
* Finally got it all to compile
* Get rid of that old KEYMAP macro
* edit readme
* Put my name everywhere and some minor code clean ups
* start to remove that kc nonsense
* fix keymap compilation issues
* add reset key info
* better human readable formatting
* match the duck default layout
* add confgurator support
* clarify reset key
* might be a good idea to use the correct pin
* get the riight keycode for RGB
* include an ALL layout
* I tried to fix the formatting....sigh
* add functons to ensure Configurator compile-ability
* move jetfire to duck directory
* Moved and renamed things as per Drashna's PR comments as his back was hurting as he reviewed this
Ryan
QMK Bot
Jouke Witteveen
Joel Challis
Drashna Jael're
Stefan Kerkmann
James Young
Zach White
MechMerlin
ytkwong
ridingqwerty
Jeremy Bernhardt