Interrupt driven Control ep and Console task

keyboard/hhkb/Makefile.lufa

@@ -93,6 +93,9 @@ ARCH = AVR8
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
 
 # Build Options
 #   comment out to disable the options.

protocol/lufa/descriptor.h

@@ -110,7 +110,7 @@ typedef struct
 
 #define KEYBOARD_EPSIZE             8
 #define MOUSE_EPSIZE                8
-#define CONSOLE_EPSIZE              8
+#define CONSOLE_EPSIZE              32
 #define EXTRA_EPSIZE                8
 
 

protocol/lufa/lufa.c

@@ -69,7 +69,7 @@ static host_driver_t lufa_driver = {
 
 
 static void SetupHardware(void);
-static void Console_HID_Task(void);
+static void Console_Task(void);
 
 int main(void)
 {
@@ -90,8 +90,9 @@ int main(void)
     while (1) {
         keyboard_proc();
 
-        Console_HID_Task();
+#if !defined(INTERRUPT_CONTROL_ENDPOINT)
         USB_USBTask();
+#endif
     }
 }
 
@@ -105,14 +106,20 @@ void SetupHardware(void)
     clock_prescale_set(clock_div_1);
 
     USB_Init();
+
+    // for Console_Task
+    USB_Device_EnableSOFEvents();
 }
 
-static void Console_HID_Task(void)
+static void Console_Task(void)
 {
     /* Device must be connected and configured for the task to run */
     if (USB_DeviceState != DEVICE_STATE_Configured)
       return;
 
+    uint8_t ep = Endpoint_GetCurrentEndpoint();
+
+#if 0
     // TODO: impl receivechar()/recvchar()
     Endpoint_SelectEndpoint(CONSOLE_OUT_EPNUM);
 
@@ -135,12 +142,16 @@ static void Console_HID_Task(void)
         /* Finalize the stream transfer to send the last packet */
         Endpoint_ClearOUT();
     }
+#endif
 
     /* IN packet */
     Endpoint_SelectEndpoint(CONSOLE_IN_EPNUM);
-        // send IN packet
-	if (Endpoint_IsINReady())
+    // flash senchar packet
+    if (Endpoint_IsINReady()) {
         Endpoint_ClearIN();
+    }
+
+    Endpoint_SelectEndpoint(ep);
 }
 
 
@@ -157,6 +168,16 @@ void EVENT_USB_Device_Disconnect(void)
 {
 }
 
+#define CONSOLE_TASK_INTERVAL 50
+void EVENT_USB_Device_StartOfFrame(void)
+{
+    static uint8_t interval;
+    if (++interval == CONSOLE_TASK_INTERVAL) {
+        Console_Task();
+        interval = 0;
+    }
+}
+
 /** Event handler for the USB_ConfigurationChanged event.
  * This is fired when the host sets the current configuration of the USB device after enumeration.
  */
@@ -182,7 +203,7 @@ void EVENT_USB_Device_ConfigurationChanged(void)
 
     /* Setup Console HID Report Endpoints */
     ConfigSuccess &= Endpoint_ConfigureEndpoint(CONSOLE_IN_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_IN,
-                                                CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE);
+                                                CONSOLE_EPSIZE, ENDPOINT_BANK_DOUBLE);
     ConfigSuccess &= Endpoint_ConfigureEndpoint(CONSOLE_OUT_EPNUM, EP_TYPE_INTERRUPT, ENDPOINT_DIR_OUT,
                                                 CONSOLE_EPSIZE, ENDPOINT_BANK_SINGLE);
 }
@@ -374,6 +395,7 @@ static void send_consumer(uint16_t data)
 /*******************************************************************************
  * sendchar
  ******************************************************************************/
+#define SEND_TIMEOUT 10
 int8_t sendchar(uint8_t c)
 {
     if (USB_DeviceState != DEVICE_STATE_Configured)
@@ -381,9 +403,9 @@ int8_t sendchar(uint8_t c)
 
     Endpoint_SelectEndpoint(CONSOLE_IN_EPNUM);
 
-    uint8_t timeout = 10;
+    uint8_t timeout = SEND_TIMEOUT;
     uint16_t prevFN = USB_Device_GetFrameNumber();
-    while (!Endpoint_IsINReady()) {
+    while (!Endpoint_IsReadWriteAllowed()) {
         switch (USB_DeviceState) {
         case DEVICE_STATE_Unattached:
         case DEVICE_STATE_Suspended:
@@ -400,7 +422,7 @@ int8_t sendchar(uint8_t c)
 
     Endpoint_Write_8(c);
 
-    // send when packet is full
+    // send when bank is full
     if (!Endpoint_IsReadWriteAllowed())
         Endpoint_ClearIN();