Re-fix the STM32 dual-bank bootloader stuff. (#9738)
* Re-fix the dual-bank bootloader stuff. * Use wait_ms() instead of using nop's for a delay, as ChibiOS is actually running at the time of bootloader jump.daktil_manuform
parent
b0335b2731
commit
686a9d35ff
|
@ -2,6 +2,7 @@
|
|||
|
||||
#include "ch.h"
|
||||
#include "hal.h"
|
||||
#include "wait.h"
|
||||
|
||||
/* This code should be checked whether it runs correctly on platforms */
|
||||
#define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
|
||||
|
@ -31,44 +32,27 @@
|
|||
|
||||
extern uint32_t __ram0_end__;
|
||||
|
||||
# define bootdelay(loopcount) \
|
||||
do { \
|
||||
for (int i = 0; i < loopcount; ++i) { \
|
||||
__asm__ volatile("nop\n\t" \
|
||||
"nop\n\t" \
|
||||
"nop\n\t"); \
|
||||
} \
|
||||
} while (0)
|
||||
|
||||
void bootloader_jump(void) {
|
||||
*MAGIC_ADDR = BOOTLOADER_MAGIC; // set magic flag => reset handler will jump into boot loader
|
||||
// For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
|
||||
// bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
|
||||
// it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
|
||||
// BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
|
||||
// #hardware channel pins for an example circuit.
|
||||
palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
|
||||
# if STM32_BOOTLOADER_DUAL_BANK_POLARITY
|
||||
palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
|
||||
# else
|
||||
palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
|
||||
# endif
|
||||
|
||||
// Wait for a while for the capacitor to charge
|
||||
wait_ms(100);
|
||||
|
||||
// Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
|
||||
NVIC_SystemReset();
|
||||
}
|
||||
|
||||
void enter_bootloader_mode_if_requested(void) {
|
||||
unsigned long *check = MAGIC_ADDR;
|
||||
if (*check == BOOTLOADER_MAGIC) {
|
||||
*check = 0;
|
||||
|
||||
// For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
|
||||
// bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
|
||||
// it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
|
||||
// BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
|
||||
// #hardware channel pins for an example circuit.
|
||||
palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
|
||||
# if STM32_BOOTLOADER_DUAL_BANK_POLARITY
|
||||
palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
|
||||
# else
|
||||
palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
|
||||
# endif
|
||||
|
||||
// Wait for a while for the capacitor to charge
|
||||
bootdelay(STM32_BOOTLOADER_DUAL_BANK_DELAY);
|
||||
|
||||
// Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
|
||||
NVIC_SystemReset();
|
||||
}
|
||||
}
|
||||
void enter_bootloader_mode_if_requested(void) {} // not needed at all, but if anybody attempts to invoke it....
|
||||
|
||||
#elif defined(STM32_BOOTLOADER_ADDRESS) // STM32_BOOTLOADER_DUAL_BANK
|
||||
|
||||
|
|
Loading…
Reference in New Issue