Adds Zlant keyboard support (#3028)
* Added Zlant support * Uses LAYOUT and identifies individual layers * Removed deprecated =? usage on rules.mk * Adds readme for Zlant keyboard and its default layout * Fixed LAYOUT constant * Minor zlant readme formatting fixdaktil_thumb_popravljen
Felipe Coury
Drashna Jaelre
parent
0026da1414
commit
575b2a66df
|
|
@ -0,0 +1,58 @@
|
|||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#include "config_common.h"
|
||||
|
||||
/* USB Device descriptor parameter */
|
||||
#define VENDOR_ID 0xFEED
|
||||
#define PRODUCT_ID 0x6060
|
||||
#define DEVICE_VER 0x0001
|
||||
#define MANUFACTURER Matthew Cordier
|
||||
#define PRODUCT Zlant
|
||||
#define DESCRIPTION keyboard firmware for Zlant
|
||||
|
||||
/* key matrix size */
|
||||
#define MATRIX_ROWS 4
|
||||
#define MATRIX_COLS 12
|
||||
|
||||
/* key matrix pins */
|
||||
#define MATRIX_ROW_PINS { B0, B1, D4, D5 }
|
||||
#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B7, D1, D2, D3, B3, B2 }
|
||||
#define UNUSED_PINS
|
||||
|
||||
/* COL2ROW or ROW2COL */
|
||||
#define DIODE_DIRECTION COL2ROW
|
||||
|
||||
/* number of backlight levels */
|
||||
|
||||
#ifdef BACKLIGHT_PIN
|
||||
#define BACKLIGHT_LEVELS 0
|
||||
#endif
|
||||
|
||||
/* Set 0 if debouncing isn't needed */
|
||||
#define DEBOUNCING_DELAY 5
|
||||
|
||||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
|
||||
#define LOCKING_SUPPORT_ENABLE
|
||||
|
||||
/* Locking resynchronize hack */
|
||||
#define LOCKING_RESYNC_ENABLE
|
||||
|
||||
/* key combination for command */
|
||||
#define IS_COMMAND() ( \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
|
||||
)
|
||||
|
||||
/* prevent stuck modifiers */
|
||||
#define PREVENT_STUCK_MODIFIERS
|
||||
|
||||
#define RGB_DI_PIN D6
|
||||
#ifdef RGB_DI_PIN
|
||||
#define RGBLIGHT_ANIMATIONS
|
||||
#define RGBLED_NUM 12
|
||||
#define RGBLIGHT_HUE_STEP 8
|
||||
#define RGBLIGHT_SAT_STEP 8
|
||||
#define RGBLIGHT_VAL_STEP 8
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,20 @@
|
|||
#include QMK_KEYBOARD_H
|
||||
|
||||
#define BASE 0
|
||||
#define FN 1
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
|
||||
[BASE] = LAYOUT(
|
||||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC,
|
||||
KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT,
|
||||
KC_ESC, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT,
|
||||
RGB_HUI, RGB_HUD, KC_LGUI, KC_LALT, KC_LSFT, KC_SPC, KC_SPC, MO(1), KC_LEFT, KC_DOWN, KC_UP, KC_RGHT),
|
||||
|
||||
[FN] = LAYOUT(
|
||||
KC_TRNS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_TRNS,
|
||||
KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS,
|
||||
KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_PGUP, KC_HOME, KC_TRNS, KC_TRNS,
|
||||
RGB_VAI, RGB_VAD, RESET, KC_PSCR, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGDN, KC_END, KC_TRNS, KC_DEL)
|
||||
|
||||
};
|
||||
|
|
@ -0,0 +1,5 @@
|
|||
|
||||
|
||||
# Default Zlant Layout
|
||||
|
||||
This is the default layout that comes flashed on the Zlant prototype.
|
||||
|
|
@ -0,0 +1,17 @@
|
|||
# Zlant
|
||||
|
||||
|
||||
|
||||
A compact 40% inspired by the Plank with a staggered layout instead.
|
||||
|
||||
Keyboard Maintainer: [Felipe Coury](https://github.com/fcoury)
|
||||
|
||||
Hardware Supported: Zlant Prototype PCB
|
||||
|
||||
Hardware Availability: Group buy soon
|
||||
|
||||
Make example for this keyboard (after setting up your build environment):
|
||||
|
||||
make zlant:default
|
||||
|
||||
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
|
||||
|
|
@ -0,0 +1,56 @@
|
|||
# MCU name
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE = no # Console for debug(+400)
|
||||
COMMAND_ENABLE = no # Commands for debug and configuration
|
||||
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
|
||||
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
|
||||
AUDIO_ENABLE = no
|
||||
RGBLIGHT_ENABLE = yes
|
||||
|
|
@ -0,0 +1 @@
|
|||
#include "zlant.h"
|
||||
|
|
@ -0,0 +1,18 @@
|
|||
#ifndef KB_H
|
||||
#define KB_H
|
||||
|
||||
#include "quantum.h"
|
||||
|
||||
#define LAYOUT( \
|
||||
K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, \
|
||||
K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, \
|
||||
K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, \
|
||||
K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311 \
|
||||
) { \
|
||||
{ K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011 }, \
|
||||
{ K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111 }, \
|
||||
{ K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211 }, \
|
||||
{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311 } \
|
||||
}
|
||||
|
||||
#endif
|
||||
Loading…
Reference in New Issue