qmk_firmware/keyboard/hhkb/not_supported/Makefile.iwrap

104 lines
2.8 KiB
Makefile
Raw Normal View History

#
# Makefile for iWRAP
#
# Target file name (without extension).
TARGET = hhkb_iwrap
# Directory common source filess exist
TOP_DIR = ../..
# Directory keyboard dependent files exist
TARGET_DIR = .
# keyboard dependent files
2012-10-17 07:25:08 +02:00
SRC = \
keymap.c \
matrix.c \
led.c
CONFIG_H = config_iwrap.h
# V-USB debug level: To use ps2_usart.c level must be 0
# ps2_usart.c requires USART to receive PS/2 signal.
OPT_DEFS = -DDEBUG_LEVEL=0
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
2012-10-17 07:25:08 +02:00
MCU = atmega328p
# Processor frequency.
# Normally the first thing your program should do is set the clock prescaler,
# so your program will run at the correct speed. You should also set this
# variable to same clock speed. The _delay_ms() macro uses this, and many
# examples use this variable to calculate timings. Do not add a "UL" here.
F_CPU = 12000000
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=2048
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
MOUSEKEY_ENABLE = yes # Mouse keys
EXTRAKEY_ENABLE = yes # Audio control and System control
CONSOLE_ENABLE = yes # Console for debug
COMMAND_ENABLE = yes # Commands for debug and configuration
#NKRO_ENABLE = yes # USB Nkey Rollover
#---------------- Programming Options --------------------------
AVRDUDE = avrdude
# Type: avrdude -c ? to get a full listing.
AVRDUDE_PROGRAMMER = usbasp
AVRDUDE_PORT =
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y
# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
# Search Path
VPATH += $(TARGET_DIR)
2012-10-17 07:25:08 +02:00
VPATH += $(TOP_DIR)
include $(TOP_DIR)/protocol/iwrap.mk
# TODO: to be selectable: V-USB, LUFA or PJRC
#include $(TOP_DIR)/protocol/vusb.mk
include $(TOP_DIR)/common.mk
include $(TOP_DIR)/rules.mk