qmk_firmware/keyboard/preonic/Makefile

162 lines
5.2 KiB
Makefile
Raw Normal View History

2015-08-21 16:46:53 +02:00
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
# Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
2016-03-30 06:43:07 +02:00
# make debug = Start either simulavr or avarice as specified for debugging,
2015-08-21 16:46:53 +02:00
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# Target file name (without extension).
2016-03-30 06:43:07 +02:00
TARGET = preonic
2015-08-21 16:46:53 +02:00
# Directory common source filess exist
TOP_DIR = ../..
2016-03-30 06:43:07 +02:00
TMK_DIR = ../../tmk_core
2015-08-21 16:46:53 +02:00
# Directory keyboard dependent files exist
TARGET_DIR = .
# # project specific files
2016-03-30 06:43:07 +02:00
SRC = preonic.c
ifdef keymap
KEYMAP = $(keymap)
endif
2015-08-21 16:46:53 +02:00
ifdef KEYMAP
2016-03-30 06:43:07 +02:00
ifneq ("$(wildcard keymaps/$(KEYMAP).c)","")
KEYMAP_FILE = keymaps/$(KEYMAP).c
2015-08-21 16:46:53 +02:00
else
2016-03-30 06:43:07 +02:00
ifneq ("$(wildcard keymaps/$(KEYMAP)/keymap.c)","")
KEYMAP_FILE = keymaps/$(KEYMAP)/keymap.c
else
$(error Keymap file does not exist)
endif
2015-08-21 16:46:53 +02:00
endif
2016-03-30 06:43:07 +02:00
else
ifneq ("$(wildcard keymaps/default.c)","")
KEYMAP_FILE = keymaps/default.c
else
KEYMAP_FILE = keymaps/default/keymap.c
endif
endif
SRC := $(KEYMAP_FILE) $(SRC)
2015-08-21 16:46:53 +02:00
CONFIG_H = config.h
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
2016-03-30 06:43:07 +02:00
# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
# NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
2015-08-21 16:46:53 +02:00
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
2016-03-30 06:45:37 +02:00
# MIDI_ENABLE = YES # MIDI controls
# AUDIO_ENABLE = YES # Audio output on port C6
2016-03-30 06:43:07 +02:00
# UNICODE_ENABLE = YES # Unicode
# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
# RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with MIDI at the same time.
ifdef BACKLIGHT_ENABLE
SRC += backlight.c
2015-08-25 18:30:32 +02:00
endif
2016-03-30 06:43:07 +02:00
2015-08-21 16:46:53 +02:00
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
2016-03-30 06:43:07 +02:00
VPATH += $(TMK_DIR)
2015-08-21 16:46:53 +02:00
2016-03-30 06:43:07 +02:00
include $(TOP_DIR)/quantum/quantum.mk