324 lines
7.9 KiB
C++
324 lines
7.9 KiB
C++
|
||
#include <OSCBundle.h>
|
||
#include <OSCBoards.h>
|
||
|
||
#include <SLIPEncodedSerial.h>
|
||
|
||
#ifdef BOARD_HAS_USB_SERIAL
|
||
SLIPEncodedUSBSerial SLIPSerial( thisBoardsSerialUSB );
|
||
#else
|
||
SLIPEncodedSerial SLIPSerial(Serial); // Change to Serial1 or Serial2 etc. for boards with multiple serial ports that don’t have Serial
|
||
#endif
|
||
|
||
|
||
//outgoing messages
|
||
|
||
OSCBundle bundleOUT;
|
||
|
||
//converts the pin to an osc address
|
||
char * numToOSCAddress( int pin){
|
||
static char s[10];
|
||
int i = 9;
|
||
|
||
s[i--]= '\0';
|
||
do
|
||
{
|
||
s[i] = "0123456789"[pin % 10];
|
||
--i;
|
||
pin /= 10;
|
||
}
|
||
while(pin && i);
|
||
s[i] = '/';
|
||
return &s[i];
|
||
}
|
||
|
||
/**
|
||
* ROUTES
|
||
*
|
||
* these are where the routing functions go
|
||
*
|
||
*/
|
||
|
||
/**
|
||
* DIGITAL
|
||
*
|
||
* called when address matched "/d"
|
||
* expected format:
|
||
* /d/(pin)
|
||
* /u = digitalRead with pullup
|
||
* (no value) = digitalRead without pullup
|
||
* (value) = digital write on that pin
|
||
*
|
||
*/
|
||
|
||
void routeDigital(OSCMessage &msg, int addrOffset ){
|
||
//match input or output
|
||
for(byte pin = 0; pin < NUM_DIGITAL_PINS; pin++){
|
||
//match against the pin number strings
|
||
int pinMatched = msg.match(numToOSCAddress(pin), addrOffset);
|
||
if(pinMatched){
|
||
//if it has an int, then it's a digital write
|
||
if (msg.isInt(0)){
|
||
pinMode(pin, OUTPUT);
|
||
digitalWrite(pin, (msg.getInt(0)>0) ? HIGH:LOW);
|
||
}
|
||
else if(msg.isFloat(0)){
|
||
analogWrite(pin, (int)(msg.getFloat(0)*255.0f));
|
||
}
|
||
|
||
//otherwise it's an digital read
|
||
//with a pullup?
|
||
else if (msg.fullMatch("/u", pinMatched+addrOffset)){
|
||
//set the pullup
|
||
pinMode(pin, INPUT_PULLUP);
|
||
//setup the output address which should be /d/(pin)/u
|
||
char outputAddress[9];
|
||
strcpy(outputAddress, "/d");
|
||
strcat(outputAddress, numToOSCAddress(pin));
|
||
strcat(outputAddress,"/u");
|
||
//do the digital read and send the results
|
||
bundleOUT.add(outputAddress).add(digitalRead(pin));
|
||
} //else without a pullup
|
||
else {
|
||
//set the pinmode
|
||
pinMode(pin, INPUT);
|
||
//setup the output address which should be /d/(pin)
|
||
char outputAddress[6];
|
||
strcpy(outputAddress, "/d");
|
||
strcat(outputAddress, numToOSCAddress(pin));
|
||
//do the digital read and send the results
|
||
bundleOUT.add(outputAddress).add(digitalRead(pin));
|
||
}
|
||
}
|
||
}
|
||
}
|
||
|
||
/**
|
||
* ANALOG
|
||
*
|
||
* called when the address matches "/a"
|
||
*
|
||
* format:
|
||
* /a/(pin)
|
||
* /u = analogRead with pullup
|
||
* (no value) = analogRead without pullup
|
||
* (digital value) = digital write on that pin
|
||
* (float value) = analogWrite on that pin
|
||
*
|
||
**/
|
||
|
||
void routeAnalog(OSCMessage &msg, int addrOffset ){
|
||
//iterate through all the analog pins
|
||
for(byte pin = 0; pin < NUM_ANALOG_INPUTS; pin++){
|
||
//match against the pin number strings
|
||
int pinMatched = msg.match(numToOSCAddress(pin), addrOffset);
|
||
if(pinMatched){
|
||
//if it has an int, then it's a digital write
|
||
if (msg.isInt(0)){
|
||
pinMode(analogInputToDigitalPin(pin), OUTPUT);
|
||
digitalWrite(analogInputToDigitalPin(pin), (msg.getInt(0) > 0)? HIGH: LOW);
|
||
}
|
||
else if(msg.isFloat(0)){
|
||
analogWrite(pin, (int)(msg.getFloat(0)*255.0f));
|
||
}
|
||
#ifdef BOARD_HAS_ANALOG_PULLUP
|
||
//with a pullup?
|
||
else if (msg.fullMatch("/u", pinMatched+addrOffset)){
|
||
//set the pullup
|
||
|
||
pinMode(analogInputToDigitalPin(pin), INPUT_PULLUP);
|
||
|
||
//setup the output address which should be /a/(pin)/u
|
||
char outputAddress[9];
|
||
strcpy(outputAddress, "/a");
|
||
strcat(outputAddress, numToOSCAddress(pin));
|
||
strcat(outputAddress,"/u");
|
||
//do the analog read and send the results
|
||
bundleOUT.add(outputAddress).add((int32_t)analogRead(pin));
|
||
} //else without a pullup
|
||
#endif
|
||
|
||
else {
|
||
//otherwise it's an analog read
|
||
//set the pinmode
|
||
|
||
pinMode(analogInputToDigitalPin(pin), INPUT);
|
||
//setup the output address which should be /a/(pin)
|
||
char outputAddress[6];
|
||
strcpy(outputAddress, "/a");
|
||
strcat(outputAddress, numToOSCAddress(pin));
|
||
//do the analog read and send the results
|
||
bundleOUT.add(outputAddress).add((int32_t)analogRead(pin));
|
||
}
|
||
}
|
||
}
|
||
}
|
||
|
||
#ifdef BOARD_HAS_TONE
|
||
/**
|
||
* TONE
|
||
*
|
||
* square wave output "/tone"
|
||
*
|
||
* format:
|
||
* /tone/pin
|
||
*
|
||
* (digital value) (float value) = frequency in Hz
|
||
* (no value) disable tone
|
||
*
|
||
**/
|
||
|
||
void routeTone(OSCMessage &msg, int addrOffset ){
|
||
//iterate through all the analog pins
|
||
for(byte pin = 0; pin < NUM_DIGITAL_PINS; pin++){
|
||
//match against the pin number strings
|
||
int pinMatched = msg.match(numToOSCAddress(pin), addrOffset);
|
||
if(pinMatched){
|
||
unsigned int frequency = 0;
|
||
//if it has an int, then it's an integers frequency in Hz
|
||
if (msg.isInt(0)){
|
||
frequency = msg.getInt(0);
|
||
} //otherwise it's a floating point frequency in Hz
|
||
else if(msg.isFloat(0)){
|
||
frequency = msg.getFloat(0);
|
||
}
|
||
else
|
||
noTone(pin);
|
||
if(frequency>0)
|
||
{
|
||
if(msg.isInt(1))
|
||
tone(pin, frequency, msg.getInt(1));
|
||
else
|
||
tone(pin, frequency);
|
||
}
|
||
}
|
||
}
|
||
}
|
||
#endif
|
||
|
||
|
||
#ifdef BOARD_HAS_CAPACITANCE_SENSING
|
||
#if defined(__MKL26Z64__)
|
||
#define NTPINS 11
|
||
const int cpins[NTPINS] = {22,23,19,18,17,16,15,0,1,3,4 };
|
||
#else
|
||
#define NTPINS 12
|
||
const int cpins[NTPINS] = {22,23,19,18,17,16,15,0,1,25,32, 33 };
|
||
#endif
|
||
|
||
void routeTouch(OSCMessage &msg, int addrOffset )
|
||
{
|
||
for(int i=0;i<NTPINS;++i)
|
||
{
|
||
const char *name = numToOSCAddress(cpins[i]);
|
||
int pinMatched = msg.match(name, addrOffset);
|
||
if(pinMatched)
|
||
{
|
||
char outputAddress[9];
|
||
strcpy(outputAddress, "/c");
|
||
strcat(outputAddress, name);
|
||
bundleOUT.add(outputAddress).add(touchRead(cpins[i]));
|
||
|
||
}
|
||
}
|
||
}
|
||
#endif
|
||
|
||
|
||
/**
|
||
* SYSTEM MESSAGES
|
||
*
|
||
* expected format:
|
||
* /s
|
||
* /m = microseconds
|
||
* /d = number of digital pins
|
||
* /a = number of analog pins
|
||
* /l integer = set the led
|
||
* /t = temperature
|
||
* /s = power supply voltage
|
||
*/
|
||
//
|
||
void routeSystem(OSCMessage &msg, int addrOffset ){
|
||
#ifdef BOARD_HAS_DIE_TEMPERATURE_SENSOR
|
||
if (msg.fullMatch("/t", addrOffset)){
|
||
bundleOUT.add("/s/t").add(getTemperature());
|
||
}
|
||
#endif
|
||
#ifdef BOARD_HAS_DIE_POWER_SUPPLY_MEASUREMENT
|
||
if (msg.fullMatch("/s", addrOffset)){
|
||
bundleOUT.add("/s/s").add(getSupplyVoltage());
|
||
}
|
||
#endif
|
||
if (msg.fullMatch("/m", addrOffset)){
|
||
bundleOUT.add("/s/m").add((int32_t)micros());
|
||
}
|
||
if (msg.fullMatch("/d", addrOffset)){
|
||
bundleOUT.add("/s/d").add(NUM_DIGITAL_PINS);
|
||
}
|
||
if (msg.fullMatch("/a", addrOffset)){
|
||
bundleOUT.add("/s/a").add(NUM_ANALOG_INPUTS);
|
||
}
|
||
if (msg.fullMatch("/l", addrOffset)){
|
||
if (msg.isInt(0)){
|
||
pinMode(LED_BUILTIN, OUTPUT);
|
||
int i = msg.getInt(0);
|
||
pinMode(LED_BUILTIN, OUTPUT);
|
||
digitalWrite(LED_BUILTIN, (i > 0)? HIGH: LOW);
|
||
bundleOUT.add("/s/l").add(i);
|
||
}
|
||
}
|
||
}
|
||
|
||
/**
|
||
* MAIN METHODS
|
||
*
|
||
* setup and loop, bundle receiving/sending, initial routing
|
||
*/
|
||
|
||
|
||
void setup() {
|
||
SLIPSerial.begin(115200); // set this as high as you can reliably run on your platform
|
||
}
|
||
|
||
//reads and routes the incoming messages
|
||
void loop(){
|
||
OSCBundle bundleIN;
|
||
int size;
|
||
|
||
while(!SLIPSerial.endofPacket())
|
||
if ((size =SLIPSerial.available()) > 0)
|
||
{
|
||
while(size--)
|
||
bundleIN.fill(SLIPSerial.read());
|
||
}
|
||
|
||
if(!bundleIN.hasError())
|
||
{
|
||
bundleIN.route("/s", routeSystem);
|
||
bundleIN.route("/a", routeAnalog);
|
||
bundleIN.route("/d", routeDigital);
|
||
#ifdef BOARD_HAS_TONE
|
||
bundleIN.route("/tone", routeTone);
|
||
#endif
|
||
#ifdef BOARD_HAS_CAPACITANCE_SENSING
|
||
bundleIN.route("/c", routeTouch);
|
||
#endif
|
||
}
|
||
bundleIN.empty();
|
||
|
||
|
||
//send the outgoing message
|
||
SLIPSerial.beginPacket();
|
||
bundleOUT.send(SLIPSerial);
|
||
SLIPSerial.endPacket();
|
||
bundleOUT.empty();
|
||
|
||
}
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|