qmk-dactyl-manuform-a/keyboards/handwired/MS_sculpt_mobile
Jack Humbert d2ff66a985 Creates a layouts/ folder for keymaps shared between keyboards (#1609)
* include variables and .h files as pp directives

* start layout compilation

* split ergodoxes up

* don't compile all layouts for everything

* might seg fault

* reset layouts variable

* actually reset layouts

* include rules.mk instead

* remove includes from rules.mk

* update variable setting

* load visualizer from path

* adds some more examples

* adds more layouts

* more boards added

* more boards added

* adds documentation for layouts

* use lowercase names for LAYOUT_

* add layout.json files for each layout

* add community folder, default keymaps for layouts

* touch-up default layouts

* touch-up layouts, some keyboard rules.mk

* update documentation for layouts

* fix up serial/i2c switches
2017-08-23 22:29:07 -04:00
..
keymaps Remove PLAY_NOTE_ARRAY usages to get rid of warning. 2017-08-20 12:32:20 -04:00
MS_sculpt_mobile.c Rename MS-sculpt-mobile to MS_scuplpt_mobile 2017-04-13 16:00:29 +03:00
MS_sculpt_mobile.h Add SKIP_VERSION option to speed up compilation 2017-04-13 16:00:29 +03:00
Makefile Add SKIP_VERSION option to speed up compilation 2017-04-13 16:00:29 +03:00
babblePaste.c Rename MS-sculpt-mobile to MS_scuplpt_mobile 2017-04-13 16:00:29 +03:00
babblePaste.h Rename MS-sculpt-mobile to MS_scuplpt_mobile 2017-04-13 16:00:29 +03:00
babblePaste.txt Add SKIP_VERSION option to speed up compilation 2017-04-13 16:00:29 +03:00
config.h Add SKIP_VERSION option to speed up compilation 2017-04-13 16:00:29 +03:00
readme.md Add SKIP_VERSION option to speed up compilation 2017-04-13 16:00:29 +03:00
rules.mk Creates a layouts/ folder for keymaps shared between keyboards (#1609) 2017-08-23 22:29:07 -04:00

readme.md

This is a way to take a Microsoft ergonomic bluetooth keyboard, and make it into a hard-wired keyboard running QMK.

The keyboard is known under several different names: Mobile Bluetooth 5000, Mobile 6000, Sculpt mobile, and Asus rebranded

I had a stack of them,since they're cheap on ebay, travel well, and are just ergo enough.

The ribbon cable is 1mm pitch, which is hard to hand solder. I bought a cheap set of "pitch adapter" boards https://www.amazon.com/Double-Sided-0-4mm-1-0-Adapter-60mmx38mm/dp/B00OK42118

Cut the original ribbon cable sockets off the bluetooth board using a razor, they're hard to desolder. They're also allow the cable to be inserted on top or bottom.

If I was going to do it again, I'd make the MCU connection come out the top of the keyboard and avoid the wires dangling out the bottom.

As I was debugging the matrix, I started to get random failures. In desparation I tried a second MCU, but had the same problems. It turns out that the ribbon cable connections can get worn. Shave a half millimeter off the end of the ribbon cable & the errors go away.

My method for discovering the matrix was to set up a KEYMAP macro that included all pins. See MATRIX_TESTING_KEYMAP if you need it. Then set up a keymap that has all printable symbols in the first 4 rows. test each key & record output. Then switch the printable symbols to the bottom 4 rows & repeat. This was enough to show the matrix.

The full original keymap for the sculpt is A B C D E F G H --->
0 b n m , . /
1 g h "
2 7 8 9 0 Del PgUp
3 p [ ] \
4 y u i o
5 ~ - += j k l ; 5 6 a s d q w e, Up left
7 F7 F8 F9 F10 F11 F12 f

-----> I J K L M N O P Q R
0 Caps FN
1 Vol+ mute Rctl vol- pgdn LCTL
2 Rshift LShift
3 Ralt LAlt
4 LGUI
5 6 bakspc 1 2 3 4 F4 F5 F6
6 Down right spc F1 F2 F3 tab
7 r t z x c v enter Esc

This works with 18 cols + 8 rows on a Teensy++, or Arm based Teensy.

The Astar mini has all pins exposed , so you can do 18x8 If you want a speaker, LEDs &etc, you'll need to free up a pin. I recommend joining columns R and L to the same pin.

Building - add ASTAR=1 to the compile line or leave out for teensy2++