qmk-dactyl-manuform-a/keyboards/boston_meetup/2019/config.h

192 lines
4.9 KiB
C

#pragma once
/* USB Device descriptor parameter */
#define DEVICE_VER 0x07E3
#undef MATRIX_ROWS
#undef MATRIX_COLS
/* key matrix size */
#define MATRIX_ROWS 4
#define MATRIX_COLS 4
/*
* Keyboard Matrix Assignments
*
* Change this to how you wired your keyboard
* COLS: AVR pins used for columns, left to right
* ROWS: AVR pins used for rows, top to bottom
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
*
*/
#undef MATRIX_ROW_PINS
#undef MATRIX_COL_PINS
#define MATRIX_ROW_PINS { A3, B8, B9, B1 }
#define MATRIX_COL_PINS { A7, A8, B2, B10 }
#define ENCODERS_PAD_A { B13 }
#define ENCODERS_PAD_B { B14 }
//Audio
#undef AUDIO_VOICES
#undef C6_AUDIO
#ifdef AUDIO_ENABLE
#define STARTUP_SONG SONG(ONE_UP_SOUND)
// #define STARTUP_SONG SONG(NO_SOUND)
#define AUDIO_CLICKY
/* to enable clicky on startup */
//#define AUDIO_CLICKY_ON
#define AUDIO_CLICKY_FREQ_RANDOMNESS 1.5f
#endif
//configure qwiic micro_oled driver for the 128x32 oled
#ifdef QWIIC_MICRO_OLED_ENABLE
#undef I2C_ADDRESS_SA0_1
#define I2C_ADDRESS_SA0_1 0b0111100
#define LCDWIDTH 128
#define LCDHEIGHT 32
#define micro_oled_rotate_180
#endif
/*
* Keyboard Matrix Assignments
*
* Change this to how you wired your keyboard
* COLS: AVR pins used for columns, left to right
* ROWS: AVR pins used for rows, top to bottom
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
*
*/
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCE 6
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
//#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
//#define LOCKING_RESYNC_ENABLE
/*
* Force NKRO
*
* Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
* state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
* makefile for this to work.)
*
* If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
* until the next keyboard reset.
*
* NKRO may prevent your keystrokes from being detected in the BIOS, but it is
* fully operational during normal computer usage.
*
* For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
* or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
* bootmagic, NKRO mode will always be enabled until it is toggled again during a
* power-up.
*
*/
//#define FORCE_NKRO
/*
* Feature disable options
* These options are also useful to firmware size reduction.
*/
/* disable debug print */
//#define NO_DEBUG
/* disable print */
//#define NO_PRINT
/* disable action features */
//#define NO_ACTION_LAYER
//#define NO_ACTION_TAPPING
//#define NO_ACTION_ONESHOT
//#define NO_ACTION_MACRO
//#define NO_ACTION_FUNCTION
/*
* MIDI options
*/
/* enable basic MIDI features:
- MIDI notes can be sent when in Music mode is on
*/
#define MIDI_BASIC
/* enable advanced MIDI features:
- MIDI notes can be added to the keymap
- Octave shift and transpose
- Virtual sustain, portamento, and modulation wheel
- etc.
*/
//#define MIDI_ADVANCED
/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
//#define MIDI_TONE_KEYCODE_OCTAVES 2
/* Haptic Driver initialization settings
* Feedback Control Settings */
#define FB_ERM_LRA 1 /* For ERM:0 or LRA:1*/
#define FB_BRAKEFACTOR 6 /* For 1x:0, 2x:1, 3x:2, 4x:3, 6x:4, 8x:5, 16x:6, Disable Braking:7 */
#define FB_LOOPGAIN 1 /* For Low:0, Medium:1, High:2, Very High:3 */
/* default 3V ERM vibration motor voltage and library*/
#if FB_ERM_LRA == 0
#define RATED_VOLTAGE 3
#define V_RMS 2.3
#define V_PEAK 3.30
/* Library Selection */
#define LIB_SELECTION 4 /* For Empty:0' TS2200 library A to D:1-5, LRA Library: 6 */
/* default 2V LRA voltage and library */
#elif FB_ERM_LRA == 1
#define RATED_VOLTAGE 2
#define V_RMS 2.0
#define V_PEAK 2.85
#define F_LRA 200
/* Library Selection */
#define LIB_SELECTION 6 /* For Empty:0' TS2200 library A to D:1-5, LRA Library: 6 */
#endif
/* Control 1 register settings */
#define DRIVE_TIME 25
#define AC_COUPLE 0
#define STARTUP_BOOST 1
/* Control 2 Settings */
#define BIDIR_INPUT 1
#define BRAKE_STAB 1 /* Loopgain is reduced when braking is almost complete to improve stability */
#define SAMPLE_TIME 3
#define BLANKING_TIME 1
#define IDISS_TIME 1
/* Control 3 settings */
#define NG_THRESH 2
#define ERM_OPEN_LOOP 1
#define SUPPLY_COMP_DIS 0
#define DATA_FORMAT_RTO 0
#define LRA_DRIVE_MODE 0
#define N_PWM_ANALOG 0
#define LRA_OPEN_LOOP 0
/* Control 4 settings */
#define ZC_DET_TIME 0
#define AUTO_CAL_TIME 3
#define RGBLIGHT_ANIMATIONS
#define RGBLED_NUM 10
#define RGB_DI_PIN B5
#define DRIVER_LED_TOTAL RGBLED_NUM
#define RGB_MATRIX_KEYPRESSES
#define SOLENOID_PIN A14