* Fix incorrect delay when setting WS2812 (and similar) leds
* Add documentation for WS2812_DELAY_MICROSECONDS
* Remove improper cast to uint8_t
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
* Remove unneeded cast to uint8_t and correct math
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
* microseconds -> µs
Co-authored-by: Ryan <fauxpark@gmail.com>
* Make documentation better match the spec sheet.
Co-authored-by: Ryan <fauxpark@gmail.com>
* Rename macro to match spec sheet
* Further correction to the delay maths for the SPI case.
Co-authored-by: Joel Challis <git@zvecr.com>
* Move ws2812_common.h to the drivers directory
* Revert "Further correction to the delay maths for the SPI case."
This reverts commit e61b56a2cfc7dfec9992a7a3af92afa50e5b8ec0.
* Remove ws2812_setleds_pin(); consolidate ws2812.h
Co-authored-by: Sergey Vlasov <sigprof@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* ARM split - Add uart half duplex transport support
* Fix for f103
* initial full duplex pass
* partially remove full duplex
* Correct speeds within driver docs
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* Update tmk_core/common/progmem.h
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update quantum/rgblight.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* fixed problem with implicit declaration in quantum/rgblight.c (#8381)
Co-authored-by: Ryan <fauxpark@gmail.com>
* Update switch to array to allow custom values
* Add adc keymap
* update docs to reflect alignment of default 10 bit
* start conversion to USE_ADCVn
* samplerate is hella wrong...stub out for now
* basic f1 and f4 functionality
* Tidy up current changes
* Restore old pinToMux function
* Add back sample rate for supported platforms
* F0 compile fixes
* wordsmithery
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Remove reference to avr only function
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add support for STM32L0/L1 onboard EEPROM.
* Update docs/eeprom_driver.md
Co-Authored-By: Joel Challis <git@zvecr.com>
Co-authored-by: Joel Challis <git@zvecr.com>
* Add buffer based single line pan, arbitrary byte write to buffer
* Change dirty mask to inverse of OLED_BLOCK_TYPE for future proofing larger buffer sizes
* Updating docs to include new functions
* Updating to clarify scroll vs pan
* Fix out of bound OLED font access
The default font is 1344 bytes, or a total of 224 glyphs (each 6-bytes wide).
OLED_FONT_END defaults to 224, which if used will then index off the end of
the font array. So either the documentation or code is wrong.
Instead of figuring out the rewording of the documentation, just change
the OLED_FONT_END default value to 223, to match the documentation and code.
* Add static assert to check array size
Build bomb if the font array size doesn't match to the defines.
- uprintf -> dprintf
- Fix atsam "vendor" eeprom.
- Bump Kinetis K20x to 64 bytes, too.
- Rollback Kinetis to 32 bytes as partitioning can only be done once. Add warning about changing the value.
- Change RAM-backed "fake" EEPROM implementations to match eeconfig's current usage.
- Add 24LC128 by request.
MelGeek
QMK Bot
Joshua Diamond
Xelus22
itsnoteasy
Wilba
Ryan
Drashna Jaelre
zvecr
Nick Brassel
Brian Mock
Casper Weiss Bang
brickbots
Drew Mills
James Young
Nick Winans
Ted M Lin