* Add pteron44
* Apply suggestions from code review
Co-authored-by: Ryan <fauxpark@gmail.com>
* Apply suggestions from code review part 2
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add my own keymap
* Layer 0: Workman
* Layer 1: RSTHD (my own take on it)
* Layer 2: Mouse
* Layer 3: Navigation
* Layer 4: Symbols right
* Layer 5: Symbols left
* Layer 6: Fn keys
* Layer 7: Numbers
* Layer 8: Vim and misceallaneaous accessible from any other layer
* Move the current code to a 0.1 folder in preparation for upcoming changes
Version 0.2 is currently being prototyped and uses an arm chip which
will need its own firmware.
There is also the Ferris sweep which uses a pro-micro compatible board
which will need its own directory.
* Move Ferris out of handwired and into the light
The keyboard is now well out of the prototype phase as tens of them have
been produced and acquired by various people.
With 0.2 coming out, adoption is going to increase again as the board
will be available for sale at some recognized vendors.
Now is probably a good time to recognize its status as more than a
prototype :)
* Add code for the Ferris Sweep (a.k.a cradio)
The Ferris Sweep is a creation of the talented @davidphilipbarr, a.k.a DPB.
It has the key layout of a Ferris and uses a pro-micro connected to the
switches via direct pins so that diodes are not needed and the soldering
is minimal.
With their blessing, I took the code for it from DPB's own repo:
https://github.com/davidphilipbarr/36keys/tree/master/qmk/cradio
and did some adaptations such as removing commented out code, enabling
EE_HANDS and mouse keys for consistency with my existing Ferris code.
* Fix indentation in rules.mk
* Fix indentation in sweep's config
* Remove unnecessary lines from sweep's rules.mk
* Remove unnecessary lines from sweep's rules.mk
* Rename 0.1 to 0_1
This avoids the dot looking like the separation between a filename and
its extension.
In the same commit, bring matrix.c to the 0_1 folder as this was needed
for the code to compile properly (matrix.c is referred to in the readme
under `0_1` and is specific to that revision of the firmware).
* Update copyright statements for Sweep
* Clean LeftyNumpad code
* Fix typo in recently renamed file
* Fix issues with keymap layout
* Initial PR Feedback fixes
* Update keyboards/handwired/leftynumpad/config.h
Co-authored-by: Joel Challis <git@zvecr.com>
* Update keyboards/handwired/leftynumpad/config.h
Co-authored-by: Joel Challis <git@zvecr.com>
* Apply suggestions from code review
Co-authored-by: Joel Challis <git@zvecr.com>
* Apply suggestions from code review
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Add fixes based on PR feedback
* Update keyboards/handwired/leftynumpad/readme.md
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Joel Challis <git@zvecr.com>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Basic keymap parsing finally works
* Add 'keymap.json' creation to the qmk.keymap module
* Add tests and fix formatting
* Fix/exclude flake8 errors
* Convert keymap.c to valid keymap.json
* Fix some errors
* Add tests
* Finalize keymap.json creation, add json template
* Add docs
* Move pygments to the standard requirements
* Add support for nameless layers, fix tests
* Fix things after rebase
* Add missing 'keymap' value.
* Fix missing layer numbers from advanced keycodes
Buckwich noticed that if the advanced keycode / layer toggling key
contains a number, it goes missing.
Now we properly handle them.
Thx for noticing!
* Apply suggestions from code review
* fixup tests
Co-authored-by: Zach White <skullydazed@drpepper.org>
Co-authored-by: skullY <skullydazed@gmail.com>
* Move my custom functions and keymaps to userspace to be able to add the STM32F411 variant of my keyboard with mostly the same functionality
* Move keymaps to community layouts
* Remove keymaps from userspace readme.md
Co-authored-by: Janos Daniel Reibl <janos.daniel.reibl@protonmail.com>
* First pass at manuform layout.
* Updates from actual usage on my board. Fixed a couple of bugs, added a stormlight quote randomizer.
* Use a 32-bit timer that can actually hit 5 minutes.
* Some updates after a day of usage:
* Turn off WPM. It's too inaccurate and takes up a decent amount of space that can be devoted to quotes.
* Turn off the OLEDs after 5 minutes
* Move the keys around a bit.
* Add many more quotes.
* Adjust the quotes to make room for missing and misswritten WoT quote. Adjusted the keymap slightly. Adjust the mods display to include one_shots.
* Revert osm on lgui as it makes start menu search impossible to use.
* Use LTO_ENABLE flag.
* License all of my (333fred's) keymaps as MIT.
* Update users/333fred/rgb.c
Co-authored-by: Ryan <fauxpark@gmail.com>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Create keymap.c
* Add files via upload
* Added files for handwired 3d printed clueboard 660
* create via layout files
* added layout files for via
* updated product ID to fix id conflicts
* change product ID to fix ID conflicts.
* fixed capitalization error that was causing issues
* fixed capitalization issues.
* fix syntax errors
* Fixed syntax errors (stray punctuation)
* Compatibility fixes
* Compatibility fixes
* Compatibility fixes
* Compatibility fixes
* capitalization fixes
* Compatibility fixes
* Compatibility fixes
* Compatibility Fixes
* Compatibility fixes
* Compatibility fixes
* Compatibility changes
* upkeep, fixing typos
* Update keyboards/handwired/3dp660/config.h
Removed Description line
* Update keyboards/handwired/3dp660/rules.mk
correct bootloader
* Update keyboards/handwired/3dp660/3dp660.h
fix case sensitive typos
* Update keyboards/handwired/3dp660/keymaps/default/keymap.c
change tab indentation to space indentations.
* Update keyboards/handwired/3dp660/keymaps/via/keymap.c
change tab indentations to space indentations
* Delete 3dp660.json
This file was for VIA, and shouldn't be in this repo. I placed it here so I wouldn't misplace it in my filesystem. My apologies.
* Update info.json
change suggestions to other file said to lowercase "ansi", caused reference issues, changed all instances of "ANSI" to "ansi".
* Update keymap.c
change suggestions to other file said to lowercase "ansi", caused reference issues, changed all instances of "ANSI" to "ansi".
* Update keymap.c
more capitalization fixes
* Update keyboards/handwired/3dp660/readme.md
shortened imgur url
* Update keyboards/handwired/3dp660/rules.mk
remove extraneous comments
* Delete config.h
* Update keyboards/handwired/3dp660/rules.mk
* Update 3dp660.c
add license headers to all .c and .h files
* Update 3dp660.h
added license header to all .c and .h files.
* Update keymap.c
added license header to all .c and .h files.
* Update keymap.c
added license header to all .c and .h files.
* Update keyboards/handwired/3dp660/readme.md
Add maintainer URL
* Update keyboards/handwired/3dp660/keymaps/default/keymap.c
remove extraneous default keymap layers
* Update keyboards/handwired/3dp660/keymaps/default/rules.mk
* Update rules.mk
Moved LTO to keyboard level.
* Update rules.mk
Moved LTO to keyboard level.
* Delete rules.mk
Made obsolete by LTO move to keyboard level.
* Update keyboards/handwired/3dp660/rules.mk
capitalization errors.
* Apply suggestions from code review
Housekeeping, changing code for readability.
Fix configs to make the `handwired/onekey/blackpill_f401:backlight` and
`handwired/onekey/blackpill_f411:backlight` examples actually compile
and work:
- Use `PWMD5` instead of `PWMD2` for backlight, which matches the
default value of `BACKLIGHT_PAL_MODE` (AF02 for pin A0 is `TIM5_CH1`)
and does not conflict with the default value of `STM32_ST_USE_TIMER`.
- Enable `HAL_USE_PWM` in halconf.h and `STM32_PWM_USE_TIM5` in
mcuconf.h, so that `PWMD5` could be used.
There is no way to invoke the command feature while having just a single
physical key, and disabling that feature fixes build for keymaps like
`handwired/onekey/promicro:rgb` without resorting to LTO (the command
feature consumes more than 4900 bytes with avr-gcc 8.4.0).
* Better handle LTO_ENABLE
Especially when calling from command line
* Replace LINK_TIME_OPTIMIZATION_ENABLE with LTO_ENABLE
* Remove long for LTO from show_options.mk
* add support for hid gamepad interface
add documentation for HID joystick
Add joystick_task to read analog axes values even when no key is pressed or release. update doc
Update docs/feature_joystick.md
Manage pin setup and read to maintain matrix scan after analog read
* Incorporates patches and changes to HID reporting
There are some patches provided by @a-chol incorporated on this commit,
and also some changes I made to the HID Report structure.
The most interesting is the one dealing with number of buttons: Linux
doesn't seem to care, but Windows requires the HID structure to be byte
aligned (that's in the spec). So if one declares 8/16/32... buttons they
should not have any issues, but this is what happens when you have 9
buttons:
```
bits |0|1|2|3|4|5|6|7|
|*|*|*|*|*|*|*|*| axis 0 (report size 8)
|*|*|*|*|*|*|*|*| ...
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*| axis 6
|*|*|*|*|*|*|*|*| first 8 buttons (report size 1)
|*| | | | | | | | last of 9 buttons, not aligned
```
So for that I added a conditonal that will add a number of reports with
size 1 to make sure it aligns to the next multiple of 8. Those reports
send dummy inputs that don't do anything aside from aligning the data.
Tested on Linux, Windows 10 and Street Fighter (where the joystick is
recognized as direct-input)
* Add save and restore of each pin used in reading joystick (AVR).
Allow output pin to be JS_VIRTUAL_AXIS if the axis is connected to Vcc
instead of an output pin from the MCU.
Fix joystick report id
Fix broken v-usb hid joystick interface. Make it more resilient to unusual settings (none multiple of eight button count, 0 buttons or 0 axes)
Correct adc reading for multiple axes. Piecewise range conversion for uncentered raw value range. Input, output and ground pin configuration per axis.
Documentation fixes
* Fix port addressing for joystick analog read
* The other required set of changes
As per the PR, the changes still holding it up.
Add onekey for testing.
Fix ARM builds.
Fix device descriptor when either axes or buttons is zero.
Add compile-time check for at least one axis or button.
Move definition to try to fix conflict.
PR review comments.
qmk cformat
* avoid float functions to compute range mapping for axis adc reading
* Remove V-USB support for now. Updated docs accordingly.
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add support for joystick adc reading for stm32 MCUs. Fix joystick hid report sending for chibios
* Fix HID joystick report sending for ChibiOS.
Add one analog axis to the onekey:joystick keymap.
Fix pin state save and restore during joystick analog read for STM32
MCUs.
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add missing mcuconf.h and halconf.h to onekey:joystick keymap.
Add suggested fixes from PR.
* Switch saveState and restoreState signature to use pin_t type.
onekey:joystick : add a second axis, virtual and programmatically animated.
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add PR corrections
* Remove halconf.h and mcuconf.h from onekey keymaps
* Change ADC_PIN to A0
Co-authored-by: achol <allecooll@hotmail.com>
Co-authored-by: José Júnior <jose.junior@gmail.com>
Co-authored-by: a-chol <achol@notamail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Initial work for consolidation of board files and default ChibiOS configs.
* Migrate F401/F411 black pills for testing.
* Add early init bootloader jump flag.
* Add support for I2C in order to use i2c_scanner keymap.
* Add F401/F411 HSE bypass to get things booting.
* Exempt "hooked" ChibiOS conf files from updater script.
* Fix up ordering for bootloader_defs file check.
* Match previous $(KEYBOARD_PATHS) value for Proton-C, updated for all board configs.
* setup handwired pteron38
* Clean up readme
* readme follow template
* c formatting conventions
* remove file size comments from rules.mk
* use direct link to imgur image
* Apply suggestions from code review
* add license
* cleaning up
* got some working bones
* working pretty well
* really livin' now
* all done
* copyright adjustments
* default keymap
* readme
* no descrip
* remove trailing slashes
* remove blank line
* remove trailing slashes
* clean up readme
* clean up rules spacing
* bootloader spacing
* made quick json from KLE converter
* remove postageboard mini references
* add actual manu and product values
* add make example
* rework
* remove double bootload define
* smoller image
* liscensed
* correct dimensions
* dimensions
* Added handwired/selene based on handwired/106_with_trackpoint
* now at least parially working
* Selene Firmware 1, ready
* Updated Readme to align more with Template
* Added URL to info.json
* Fix status Lights being wired incorrectly
* Update keyboards/handwired/selene/config.h
* Update keyboards/handwired/selene/keymaps/Bpendragon/keymap.c
* Update keyboards/handwired/selene/selene.c
* Update keyboards/handwired/selene/selene.h
* Changes for PR requested by fauxpark
* Adds `default` keymap
* Renames `Bpendragon` to `bpendragon`
* Removes uneeded descriptors and options
* Simplifies return statement in `keymap.c`
* Removes trailing slashes from layout in `keymap.c`
* Updates `readme.mk` to reflect default keymap
* Aligns comments in `rules.mk`
* Forced folder name update to lowercase
* Apply suggestions from code review
Ryan
Reibl János Dániel
Erovia
Filip Paryż
Fidel Coria
Pierre Chevalier
Evgenii
Tom Swartz
Sergey Vlasov
Fred Silberberg
Brandon Claveria
Joel Schneider
QMK Bot
gooberpsycho
Dmitry Nosachev
Spaceman
James Young
Zach White
Drashna Jaelre
flehrad
a-chol
Nick Brassel
myoung34
Blake
Rossman360
David Camp