* Rewrite APA102 support
The APA102 source was broken by commit 16a15c1cfc as it did not include the
quantum header. This commit addresses that, as well as other issues with
transferring bytes over the SPI interface, i.e. it was not setting the
clock pin back to low after sending a bit.
The deviation when sending the end frame is kept, but updated to the
latest from the referenced project.
Finally, these changes expose the global LED brightness parameter
of the APA102. Brightness values are configurable through
`APA102_DEFAULT_BRIGHTNESS` and `APA102_MAX_BRIGHTNESS`.
* Fix typo in led brightness extern
* Move driver out of AVR directory and add delay for ARM
* Experimental APA102 support on AVR and ARM
Co-authored-by: Alde Rojas <hello@alde.io>
* Refactor apa102_send_byte() calls to a loop
* Implement io_wait function for ARM
* Move APA102 drivers to own directory, fix copyright notice
* Add APA102 keymap to handwired/onekey
* Simplify RGBLIGHT_ENABLE/DRIVER option handling
Co-authored-by: Mikkel Jeppesen <2756925+Duckle29@users.noreply.github.com>
* Disable almost all ChibiOS subsystems.
* Modify ChibiOS config updater script to fixup mcuconf include, use develop as base instead of master.
* Add default early-init bootloader to F042/F072.
* Back to 100k freq.
- Set all other ChibiOS defaults to 'off', when not targeting Proton-C
- Modified all existing F303 boards to point at the QMK_PROTON_C to ensure repeatable binary output
- Modified version.h generation so that SKIP_VERSION=yes generates the same output
By default the `i2c_master` driver for ChibiOS uses the B6 pin for
`I2C1_SCL` and the B7 pin for `I2C1_SDA`. However, the ChibiOS board
file used for the F401 Blackpill board (`ST_STM32F401C_DISCOVERY`)
configures B6 as `I2C1_SCL` and B9 as `I2C1_SDA`, and if that
configuration is left unchanged, enabling the `i2c_master` driver
results in having two pins (B7 and B9) configured as `I2C1_SDA` at the
same time, which does not work properly (experimental results show that
the B9 pin still works as `I2C1_SDA` in that case, and the B7 pin does
not work).
Configure the B9 pin as an input with pull-up in `board_init()`, so that
the B7 pin can be configured as `I2C1_SDA` by the I2C driver.
* Basic keymap parsing finally works
* Add 'keymap.json' creation to the qmk.keymap module
* Add tests and fix formatting
* Fix/exclude flake8 errors
* Convert keymap.c to valid keymap.json
* Fix some errors
* Add tests
* Finalize keymap.json creation, add json template
* Add docs
* Move pygments to the standard requirements
* Add support for nameless layers, fix tests
* Fix things after rebase
* Add missing 'keymap' value.
* Fix missing layer numbers from advanced keycodes
Buckwich noticed that if the advanced keycode / layer toggling key
contains a number, it goes missing.
Now we properly handle them.
Thx for noticing!
* Apply suggestions from code review
* fixup tests
Co-authored-by: Zach White <skullydazed@drpepper.org>
Co-authored-by: skullY <skullydazed@gmail.com>
Fix configs to make the `handwired/onekey/blackpill_f401:backlight` and
`handwired/onekey/blackpill_f411:backlight` examples actually compile
and work:
- Use `PWMD5` instead of `PWMD2` for backlight, which matches the
default value of `BACKLIGHT_PAL_MODE` (AF02 for pin A0 is `TIM5_CH1`)
and does not conflict with the default value of `STM32_ST_USE_TIMER`.
- Enable `HAL_USE_PWM` in halconf.h and `STM32_PWM_USE_TIM5` in
mcuconf.h, so that `PWMD5` could be used.
There is no way to invoke the command feature while having just a single
physical key, and disabling that feature fixes build for keymaps like
`handwired/onekey/promicro:rgb` without resorting to LTO (the command
feature consumes more than 4900 bytes with avr-gcc 8.4.0).
* add support for hid gamepad interface
add documentation for HID joystick
Add joystick_task to read analog axes values even when no key is pressed or release. update doc
Update docs/feature_joystick.md
Manage pin setup and read to maintain matrix scan after analog read
* Incorporates patches and changes to HID reporting
There are some patches provided by @a-chol incorporated on this commit,
and also some changes I made to the HID Report structure.
The most interesting is the one dealing with number of buttons: Linux
doesn't seem to care, but Windows requires the HID structure to be byte
aligned (that's in the spec). So if one declares 8/16/32... buttons they
should not have any issues, but this is what happens when you have 9
buttons:
```
bits |0|1|2|3|4|5|6|7|
|*|*|*|*|*|*|*|*| axis 0 (report size 8)
|*|*|*|*|*|*|*|*| ...
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*| axis 6
|*|*|*|*|*|*|*|*| first 8 buttons (report size 1)
|*| | | | | | | | last of 9 buttons, not aligned
```
So for that I added a conditonal that will add a number of reports with
size 1 to make sure it aligns to the next multiple of 8. Those reports
send dummy inputs that don't do anything aside from aligning the data.
Tested on Linux, Windows 10 and Street Fighter (where the joystick is
recognized as direct-input)
* Add save and restore of each pin used in reading joystick (AVR).
Allow output pin to be JS_VIRTUAL_AXIS if the axis is connected to Vcc
instead of an output pin from the MCU.
Fix joystick report id
Fix broken v-usb hid joystick interface. Make it more resilient to unusual settings (none multiple of eight button count, 0 buttons or 0 axes)
Correct adc reading for multiple axes. Piecewise range conversion for uncentered raw value range. Input, output and ground pin configuration per axis.
Documentation fixes
* Fix port addressing for joystick analog read
* The other required set of changes
As per the PR, the changes still holding it up.
Add onekey for testing.
Fix ARM builds.
Fix device descriptor when either axes or buttons is zero.
Add compile-time check for at least one axis or button.
Move definition to try to fix conflict.
PR review comments.
qmk cformat
* avoid float functions to compute range mapping for axis adc reading
* Remove V-USB support for now. Updated docs accordingly.
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add support for joystick adc reading for stm32 MCUs. Fix joystick hid report sending for chibios
* Fix HID joystick report sending for ChibiOS.
Add one analog axis to the onekey:joystick keymap.
Fix pin state save and restore during joystick analog read for STM32
MCUs.
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add missing mcuconf.h and halconf.h to onekey:joystick keymap.
Add suggested fixes from PR.
* Switch saveState and restoreState signature to use pin_t type.
onekey:joystick : add a second axis, virtual and programmatically animated.
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add PR corrections
* Remove halconf.h and mcuconf.h from onekey keymaps
* Change ADC_PIN to A0
Co-authored-by: achol <allecooll@hotmail.com>
Co-authored-by: José Júnior <jose.junior@gmail.com>
Co-authored-by: a-chol <achol@notamail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Initial work for consolidation of board files and default ChibiOS configs.
* Migrate F401/F411 black pills for testing.
* Add early init bootloader jump flag.
* Add support for I2C in order to use i2c_scanner keymap.
* Add F401/F411 HSE bypass to get things booting.
* Exempt "hooked" ChibiOS conf files from updater script.
* Fix up ordering for bootloader_defs file check.
* Match previous $(KEYBOARD_PATHS) value for Proton-C, updated for all board configs.
* I2C_TIMEOUT is not defined on arm teensy
* Work round teensy having different ChibiOS config options
* Stash OLED conf files
* update comment
* update comment
* Remove stm32 alias to allow teensy alt mode
* Set backlight and RGB pins for AVR onekeys
* Set pin for ADC as well
* Define ADC_PIN for F4 blackpills
* Use A0 for F4 ADCs
* Set ADC pins for F0 and F1
* Update switch to array to allow custom values
* Add adc keymap
* update docs to reflect alignment of default 10 bit
* start conversion to USE_ADCVn
* samplerate is hella wrong...stub out for now
* basic f1 and f4 functionality
* Tidy up current changes
* Restore old pinToMux function
* Add back sample rate for supported platforms
* F0 compile fixes
* wordsmithery
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Remove reference to avr only function
Co-authored-by: Ryan <fauxpark@gmail.com>
Clean up checks and logics that are unnecessary due to MILC updates.
Use pathlib instead of os.path for readability.
Use the 'pytest' keyboard for the tests.
Add community layout for 'handwired/onekey/pytest' so we can test
community layouts.
Nick Brassel
Ryan
QMK Bot
Zach White
Joel Challis
Aldehir Rojas
Sergey Vlasov
Erovia
James Young
a-chol
Nico Cesar
James Young