* resolve race condition between suspend and wake in LUFA
* avoid multiple calls to suspend_power_down() / suspend_wakeup_init()
* Remove duplicate suspend_power_down_kb() call
* pause on wakeup to wait for USB state to settle
* need the repeated suspend_power_down() (that's where the sleep is)
* more efficient implementation
* fine tune the pause after sending wakeup
* speculative chibios version of pause-after-wake
* make wakeup delay configurable, and adjust value
* better location for wakeup delay
* Branch point for 2020 November 28 Breaking Change
* Remove matrix_col_t to allow MATRIX_ROWS > 32 (#10183)
* Add support for soft serial to ATmega32U2 (#10204)
* Change MIDI velocity implementation to allow direct control of velocity value (#9940)
* Add ability to build a subset of all keyboards based on platform.
* Actually use eeprom_driver_init().
* Make bootloader_jump weak for ChibiOS. (#10417)
* Joystick 16-bit support (#10439)
* Per-encoder resolutions (#10259)
* Share button state from mousekey to pointing_device (#10179)
* Add hotfix for chibios keyboards not wake (#10088)
* Add advanced/efficient RGB Matrix Indicators (#8564)
* Naming change.
* Support for STM32 GPIOF,G,H,I,J,K (#10206)
* Add milc as a dependency and remove the installed milc (#10563)
* ChibiOS upgrade: early init conversions (#10214)
* ChibiOS upgrade: configuration file migrator (#9952)
* Haptic and solenoid cleanup (#9700)
* XD75 cleanup (#10524)
* OLED display update interval support (#10388)
* Add definition based on currently-selected serial driver. (#10716)
* New feature: Retro Tapping per key (#10622)
* Allow for modification of output RGB values when using rgblight/rgb_matrix. (#10638)
* Add housekeeping task callbacks so that keyboards/keymaps are capable of executing code for each main loop iteration. (#10530)
* Rescale both ChibiOS and AVR backlighting.
* Reduce Helix keyboard build variation (#8669)
* Minor change to behavior allowing display updates to continue between task ticks (#10750)
* Some GPIO manipulations in matrix.c change to atomic. (#10491)
* qmk cformat (#10767)
* [Keyboard] Update the Speedo firmware for v3.0 (#10657)
* Maartenwut/Maarten namechange to evyd13/Evy (#10274)
* [quantum] combine repeated lines of code (#10837)
* Add step sequencer feature (#9703)
* aeboards/ext65 refactor (#10820)
* Refactor xelus/dawn60 for Rev2 later (#10584)
* add DEBUG_MATRIX_SCAN_RATE_ENABLE to common_features.mk (#10824)
* [Core] Added `add_oneshot_mods` & `del_oneshot_mods` (#10549)
* update chibios os usb for the otg driver (#8893)
* Remove HD44780 References, Part 4 (#10735)
* [Keyboard] Add Valor FRL TKL (+refactor) (#10512)
* Fix cursor position bug in oled_write_raw functions (#10800)
* Fixup version.h writing when using SKIP_VERSION=yes (#10972)
* Allow for certain code in the codebase assuming length of string. (#10974)
* Add AT90USB support for serial.c (#10706)
* Auto shift: support repeats and early registration (#9826)
* Rename ledmatrix.h to match .c file (#7949)
* Split RGB_MATRIX_ENABLE into _ENABLE and _DRIVER (#10231)
* Split LED_MATRIX_ENABLE into _ENABLE and _DRIVER (#10840)
* Merge point for 2020 Nov 28 Breaking Change
* add support for hid gamepad interface
add documentation for HID joystick
Add joystick_task to read analog axes values even when no key is pressed or release. update doc
Update docs/feature_joystick.md
Manage pin setup and read to maintain matrix scan after analog read
* Incorporates patches and changes to HID reporting
There are some patches provided by @a-chol incorporated on this commit,
and also some changes I made to the HID Report structure.
The most interesting is the one dealing with number of buttons: Linux
doesn't seem to care, but Windows requires the HID structure to be byte
aligned (that's in the spec). So if one declares 8/16/32... buttons they
should not have any issues, but this is what happens when you have 9
buttons:
```
bits |0|1|2|3|4|5|6|7|
|*|*|*|*|*|*|*|*| axis 0 (report size 8)
|*|*|*|*|*|*|*|*| ...
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*|
|*|*|*|*|*|*|*|*| axis 6
|*|*|*|*|*|*|*|*| first 8 buttons (report size 1)
|*| | | | | | | | last of 9 buttons, not aligned
```
So for that I added a conditonal that will add a number of reports with
size 1 to make sure it aligns to the next multiple of 8. Those reports
send dummy inputs that don't do anything aside from aligning the data.
Tested on Linux, Windows 10 and Street Fighter (where the joystick is
recognized as direct-input)
* Add save and restore of each pin used in reading joystick (AVR).
Allow output pin to be JS_VIRTUAL_AXIS if the axis is connected to Vcc
instead of an output pin from the MCU.
Fix joystick report id
Fix broken v-usb hid joystick interface. Make it more resilient to unusual settings (none multiple of eight button count, 0 buttons or 0 axes)
Correct adc reading for multiple axes. Piecewise range conversion for uncentered raw value range. Input, output and ground pin configuration per axis.
Documentation fixes
* Fix port addressing for joystick analog read
* The other required set of changes
As per the PR, the changes still holding it up.
Add onekey for testing.
Fix ARM builds.
Fix device descriptor when either axes or buttons is zero.
Add compile-time check for at least one axis or button.
Move definition to try to fix conflict.
PR review comments.
qmk cformat
* avoid float functions to compute range mapping for axis adc reading
* Remove V-USB support for now. Updated docs accordingly.
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/usb_descriptor.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add support for joystick adc reading for stm32 MCUs. Fix joystick hid report sending for chibios
* Fix HID joystick report sending for ChibiOS.
Add one analog axis to the onekey:joystick keymap.
Fix pin state save and restore during joystick analog read for STM32
MCUs.
* Update tmk_core/protocol/chibios/usb_main.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update tmk_core/protocol/lufa/lufa.c
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add missing mcuconf.h and halconf.h to onekey:joystick keymap.
Add suggested fixes from PR.
* Switch saveState and restoreState signature to use pin_t type.
onekey:joystick : add a second axis, virtual and programmatically animated.
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Update docs/feature_joystick.md
Co-Authored-By: Ryan <fauxpark@gmail.com>
* Add PR corrections
* Remove halconf.h and mcuconf.h from onekey keymaps
* Change ADC_PIN to A0
Co-authored-by: achol <allecooll@hotmail.com>
Co-authored-by: José Júnior <jose.junior@gmail.com>
Co-authored-by: a-chol <achol@notamail.com>
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: Ryan <fauxpark@gmail.com>
* Change _delay_ms/us() to wait_ms/us()
* Switch to platform-agnostic GPIO macros
* Add AVR spi_master and migrate Adafruit BLE code
* Set verbose back to false
* Add clock divisor, bit order and SPI mode configuration for init
* Add start and stop functions
* Move configuration of mode, endianness and speed to `spi_start()`
* Some breaks here would be good
* Default Adafruit BLE clock divisor to 4 (2MHz on the Feather 32U4)
* Remove mode and divisor enums
* Add some docs
* No hr at EOF
* Add links in sidebar
* Remove unnecessary import of rgblight.h in tmk_core/protocol/*/*.c
* tmk_core/protocol/chibios/main.c
* tmk_core/protocol/lufa/lufa.c
see #8380 for tmk_core/protocol/vusb/main.c.
* Remove '#include "rgblight.h"' from tmk_core/protocol/vusb/main.c.
* Moved contents of rgblight_reconfig.h to rgblight_post_config.h.
In #3582, rgblight_reconfig.h had to be newly created. Now, the build system of qmk_firmware has a post_cofig feature, so that what was done in rgblight_reconfig.h can now be realized in rgblight_post_config.h.
**This commit does not change the build result.**
Testing script
```shell
# build on master
git checkout master
echo master > /tmp/master_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/master_md5.txt
# build on refactor_rgblight_reconfig.h
git checkout refactor_rgblight_reconfig.h
echo refactor_rgblight_reconfig.h > /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = no
make HELIX=verbose helix/rev2:default:clean
make HELIX=verbose helix/rev2:default
md5 helix_rev2_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, with animations
make HELIX=verbose helix/rev2/back:default:clean
make HELIX=verbose helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
# RGBLIGHT_ENABLE = yes, without animations
make HELIX=verbose,no_ani helix/rev2/back:default:clean
make HELIX=verbose,no_ani helix/rev2/back:default
md5 helix_rev2_back_default.hex >> /tmp/branch_md5.txt
diff -u /tmp/master_md5.txt /tmp/branch_md5.txt
```
Test result:
```
--- /tmp/master_md5.txt 2020-01-03 15:42:22.000000000 +0900
+++ /tmp/branch_md5.txt 2020-01-03 15:42:42.000000000 +0900
@@ -1,4 +1,4 @@
-master
+refactor_rgblight_reconfig.h
MD5 (helix_rev2_default.hex) = f360032edd522448366d471d8f4f8181
MD5 (helix_rev2_back_default.hex) = 0c663acc6cccc44476b3b969ad22a48f
MD5 (helix_rev2_back_default.hex) = e66b1195ff6d38e6e22c975b8ae42fd3
```
* Expressions that are too long are difficult to read, so wrap them.
* Edit the expression again
* remove `defined(RGBLIGHT_ANIMATIONS)` in `tmk_core/common/*/suspend.c`, `tmk_core/protocol/*/main.c`
move contents of rgblight_reconfig.h to rgblight.h.
The following changes were made to rgblight.h.
```diff
+#ifdef RGBLIGHT_USE_TIMER
void rgblight_task(void);
void rgblight_timer_init(void);
void rgblight_timer_enable(void);
void rgblight_timer_disable(void);
void rgblight_timer_toggle(void);
+#else
+#define rgblight_task()
+#define rgblight_timer_init()
+#define rgblight_timer_enable()
+#define rgblight_timer_disable()
+#define rgblight_timer_toggle()
+#endif
```
The following changes were made to tmk_core/common/avr/suspend.c, tmk_core/common/chibios/suspend.c, tmk_core/protocol/chibios/main.c, tmk_core/protocol/lufa/lufa.c, tmk_core/protocol/vusb/main.c.
```diff
-# ifdef RGBLIGHT_ANIMATIONS
rgblight_timer_enable();
-# endif
```
```diff
-#if defined(RGBLIGHT_ANIMATIONS) && defined(RGBLIGHT_ENABLE)
+#if defined(RGBLIGHT_ENABLE)
rgblight_task();
#endif
```
* remove 'defined(RGBLIGHT_ANIMATIONS)' in tmk_core/common/keyboard.c
Co-authored-by: Joel Challis <git@zvecr.com>
* Dedupe extrakey report struct, and send functions in V-USB & LUFA
* Doc comment for consistency
* Wrap it in ifdef to prevent unused function error
* Do the same for ATSAM
* Fix battery level code in adafruit_ble.cpp
The code in tsk_core/protocol/lufa/adafluit_ble.cpp that polls the
battery level for the Adafruit feather BLE controller reads the
regulated voltage, not the raw voltage coming from the battery. To do
that, the Adafruit Feather docs say you should read from pin A9:
https://learn.adafruit.com/adafruit-feather-32u4-basic-proto/power-management#measuring-battery-4-9.
(See also
https://learn.adafruit.com/adafruit-feather-32u4-bluefruit-le/pinouts#logic-pins-2-9.)
I'm not sure why, but analogRead(9); doesn't read the correct pin.
Checking all available analog pins experimentally, it turns out that
analogRead(7); returns the correct value. So the code above should read:
state.vbat = analogRead(7);
* Update tmk_core/protocol/lufa/adafruit_ble.cpp
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Remove old comment
* Fix linking error
* Remove `#ifdef` around `#include analog.h`.
* Really fix linking error
When this if statement is false, it will cause the report ID to be read as the LED state.
We already know there are two bytes in the endpoint, which is a reasonably good indicator that it contains a report ID, so we should always read both.
* Check the size of the SET_REPORT packet
If we have two bytes, that probably means the first is a report ID. The 6KRO interface may or may not have one, but the NKRO interface always does, so we need to check this regardless of whether KEYBOARD_SHARED_EP is defined.
* Fix indentation
* Unify multiple HID interfaces into one
This reduces the number of USB endpoints required, which frees them up
for other things.
NKRO and EXTRAKEY always use the shared endpoint.
By default, MOUSEKEY also uses it. This means it won't work as a Boot
Procotol mouse in some BIOSes, etc. If you really think your
keyboard needs to work as a mouse in your BIOS, set
MOUSE_SHARED_EP = no in your rules.mk.
By default, the core keyboard does not use the shared endpoint, as not
all BIOSes are standards compliant and that's one place you don't want
to find out your keyboard doesn't work.. If you are really confident,
you can set KEYBOARD_SHARED_EP = yes to use the shared endpoint here
too.
* unify endpoints: ChibiOS protocol implementation
* fixup: missing #ifdef EXTRAKEY_ENABLEs
broke build on AVR with EXTRAKEY disabled
* endpoints: restore error when too many endpoints required
* lufa: wait up to 10ms to send keyboard input
This avoids packets being dropped when two reports are sent in quick
succession (eg. releasing a dual role key).
* endpoints: fix compile on ARM_ATSAM
* endpoint: ARM_ATSAM fixes
No longer use wrong or unexpected endpoint IDs
* endpoints: accommodate VUSB protocol
V-USB has its own, understandably simple ideas about the report formats.
It already blasts the mouse and extrakeys through one endpoint with
report IDs. We just stay out of its way.
* endpoints: document new endpoint configuration options
* endpoints: respect keyboard_report->mods in NKRO
The caller(s) of host_keyboard_send expect to be able to just drop
modifiers in the mods field and not worry about whether NKRO is in use.
This is a good thing. So we just shift it over if needs be.
* endpoints: report.c: update for new keyboard_report format
* add temporary test code rgblight-macro-test1.[ch]
* rgblight.h : mode auto numberring and auto generate mode name symbol
No change in build result.
* rgblight.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* quantum.c use RGBLIGHT_MODE_xxx symbols
No change in build result.
* fix build break. when RGB_MATRIX_ENABLE defined
* add temporary test code rgblight-macro-test2.[ch]
* modify rgblight_mode_eeprom_helper() and rgblight_sethsv_eeprom_helper()
* modify rgblight_task()
* configurable each effect compile on/off in config.h
* update docs/feature_rgblight.md
* fix conflict. docs/feature_rgblight.md
* remove temporary test code rgblight-macro-test*.[ch]
* fix comment typo.
* remove old mode number from comment
* update docs/feature_rgblight.md about effect mode
* Revert "update docs/feature_rgblight.md about effect mode"
This reverts commit 43890663fcc9dda1899df7a37d382fc38b1a6d6d.
* some change docs/feature_rgblight.md
* fix typo
* docs/feature_rgblight.md update: revise mode number table
* Generate api docs from source code
* Add a bunch of doxygen comments
* more doxygen comments
* Add the in-progress api docs
* script to generate docs from travis
* Add doc generation to the travis job
* make travis_docs.sh commit the work it does
* make sure the docs script exits cleanly
* Move lufa descriptor to protocol/usb_descriptor
* Try to compile usb_descriptor on ChibiOS
* Add lufa_utils for ChibiOS
Lufa USB descriptors for ChibiOS
* More lufa_util compatibility fixes
* First compiling version of shared USB descriptor
* Send the usb descriptors
* Fix the CONSOLE output on ChibiOS
* Add errors for unsupported interfaces
* Enable support for vitual serial port USB descriptors
* Implement virtual serial port for ChibiOS
* Cleanup the lufa_utils
Use the default lufa header files
* Add raw hid support for ChibiOS
This is completely untested
* Enable midi compilation on ChibiOS
* Move midi functionality out of lufa.c
* Don't register sysex callback when not needed
* ChibiOS compilation fixes
* Update ChibiOS submodule
* Fix the Midi USB descriptor
It didn't work properly when both Midi and Virtual serial port was enabled.
* Add MIDI support for ChibiOS
* Fix USB descriptor strings on ChibiOS
* Use serial usb driver for raw hid
* Generalize the ChibiOS stream like drivers
This makes the initialization much more simple and eliminates a lot of
the code duplication.
* Convert console output to chibios stream driver
* Fixes for ChibiOS update
* Update the ChibiOS contrib submodule
To include the usb data toggle synchronization fixes
* Fix duplicate reset enumeration on ChibiOS
* Add missing include
* Add number of endpoints check for ChibiOS
* Enable serial USB driver on all keyboards
* Add missing includes when API is enabled withot midi
* Add another missing inlcude
* Add NIU Mini keymap from Planck keymap
* Remove old keymap files
* Fix README, removed Planck references
* Add default layout, move Planck layout to separate folder
* Update README
* Add my XD60 keymap
* Change RShift to slash
* Fix keymap: stuck on MO(1)
* Move RESET to Fn+Enter
* Add: RGB saturation cycle
* Add numpad layer to keymap
* Fix last case
* Cleanup Mechmini keymap. Once the custom RGB function is defined, there is no need to manually handle RGB code.
* Change default to KEYMAP_MIT, not KEYMAP_OFFSET
* Add custom RGB code for JJ40
* Reset Mechmini advertised power draw to 500. Will have to test actual maximum power draw later.
* RGB working on JJ40.
* Fix: saturation increase/decrease flipped
* Add new directory for my custom keymap with RGB keycodes
* Swap LAlt and LGUI
* Update JJ40 max power draw with measured value
* Update: fun40 rules.mk to enable underglow; earlier failed Travis CI
* Fix: init RGB LEDs on boot. Also added HHKB-like keymap for XD60.
* Super rudimentary backlight test, init RGB LEDs on boot
* Backlighting works - stays on for now
* Toggling working
* Now can override backlight.c functions. Problem was functions in backlight.c weren't called before due to a lack of matrix_scan_quantum() in matrix.c
* Timers not working
* Delete global.h
* Cleanup
* Compiles
* Good sign: LEDs stop working again
* Handle timer1 overflow
* Progress: fix: forgot to init
* Backlighting fully working now except breathing.
* Revert keymap to original keycodes
* Update XD60 keymap README
* Update JJ40 keymap with backlight toggles
* Breathing working just fine.
* Update references
* Add backlight_set() call
* Cleanup code to disable backlight
* Fix: does not compile
* Fix: missing call to rgblight_task.
* Testing with BACKLIGHT_BREATHING
* Cleanup
* Cleanup comments
* More commenting cleanup.
* Do not enable BACKLIGHT_BREATHING by default
* Update XD60 keymap
* Update: move matrix_scan_kb out from matrix.c to jj40.c (kb-level)
* Cleanup for PR
* Fix conflict in readme.md for NIU mini
* Restore original power consumption figure
* Fix: matrix_scan_user() now has to be defined in the keymaps
* Add weak `matrix_scan_user` so it does not have to be defined in keymap
* Add weak matrix_init_user()
Joshua Diamond
Ryan
James Young
QMK Bot
a-chol
Nick Brassel
Joel Challis
Takeshi ISHII
xyzz
bwhelm
skullY
James Laird-Wah
skullydazed
fredizzimo
Kenneth Aloysius
Jack Humbert
Benjamin Dengler
Wilba6582
Joe Wasson
Priyadi Iman Nurcahyo
yiancar
Travis La Marr