Add Teensy2 Atreus support
Sean Caffery
parent
0a71166a2d
commit
c363d6b061
|
|
@ -0,0 +1,139 @@
|
|||
#----------------------------------------------------------------------------
|
||||
# On command line:
|
||||
#
|
||||
# make all = Make software.
|
||||
#
|
||||
# make clean = Clean out built project files.
|
||||
#
|
||||
# make coff = Convert ELF to AVR COFF.
|
||||
#
|
||||
# make extcoff = Convert ELF to AVR Extended COFF.
|
||||
#
|
||||
# make program = Download the hex file to the device.
|
||||
# Please customize your programmer settings(PROGRAM_CMD)
|
||||
#
|
||||
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
||||
# (must have teensy_loader_cli installed).
|
||||
#
|
||||
# make dfu = Download the hex file to the device, using dfu-programmer (must
|
||||
# have dfu-programmer installed).
|
||||
#
|
||||
# make flip = Download the hex file to the device, using Atmel FLIP (must
|
||||
# have Atmel FLIP installed).
|
||||
#
|
||||
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
|
||||
# (must have dfu-programmer installed).
|
||||
#
|
||||
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
|
||||
# (must have Atmel FLIP installed).
|
||||
#
|
||||
# make debug = Start either simulavr or avarice as specified for debugging,
|
||||
# with avr-gdb or avr-insight as the front end for debugging.
|
||||
#
|
||||
# make filename.s = Just compile filename.c into the assembler code only.
|
||||
#
|
||||
# make filename.i = Create a preprocessed source file for use in submitting
|
||||
# bug reports to the GCC project.
|
||||
#
|
||||
# To rebuild project do "make clean" then "make all".
|
||||
#----------------------------------------------------------------------------
|
||||
|
||||
# Target file name (without extension).
|
||||
TARGET = atreus
|
||||
|
||||
|
||||
# Directory common source filess exist
|
||||
TOP_DIR = ../..
|
||||
TMK_DIR = ../../tmk_core
|
||||
|
||||
# Directory keyboard dependent files exist
|
||||
TARGET_DIR = .
|
||||
|
||||
# # project specific files
|
||||
SRC = atreus.c
|
||||
|
||||
ifdef KEYMAP
|
||||
SRC := keymaps/keymap_$(KEYMAP).c $(SRC)
|
||||
else
|
||||
SRC := keymaps/keymap_default.c $(SRC)
|
||||
endif
|
||||
|
||||
CONFIG_H = config.h
|
||||
|
||||
# MCU name
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||||
#MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||||
#EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||||
COMMAND_ENABLE = yes # Commands for debug and configuration
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
|
||||
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
||||
# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
|
||||
# MIDI_ENABLE = YES # MIDI controls
|
||||
UNICODE_ENABLE = YES # Unicode
|
||||
# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
|
||||
|
||||
# Optimize size but this may cause error "relocation truncated to fit"
|
||||
#EXTRALDFLAGS = -Wl,--relax
|
||||
|
||||
# Search Path
|
||||
VPATH += $(TARGET_DIR)
|
||||
VPATH += $(TOP_DIR)
|
||||
VPATH += $(TMK_DIR)
|
||||
|
||||
include $(TOP_DIR)/quantum/quantum.mk
|
||||
|
||||
|
|
@ -0,0 +1,180 @@
|
|||
atreus keyboard firmware
|
||||
======================
|
||||
|
||||
## Quantum MK Firmware
|
||||
|
||||
You have access to a bunch of goodies! Check out the Makefile to enable/disable some of the features. Uncomment the `#` to enable them. Setting them to `no` does nothing and will only confuse future you.
|
||||
|
||||
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
|
||||
MIDI_ENABLE = yes # MIDI controls
|
||||
# UNICODE_ENABLE = yes # Unicode support - this is commented out, just as an example. You have to use #, not //
|
||||
BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
|
||||
## Quick aliases to common actions
|
||||
|
||||
Your keymap can include shortcuts to common operations (called "function actions" in tmk).
|
||||
|
||||
### Switching and toggling layers
|
||||
|
||||
`MO(layer)` - momentary switch to *layer*. As soon as you let go of the key, the layer is deactivated and you pop back out to the previous layer. When you apply this to a key, that same key must be set as `KC_TRNS` on the destination layer. Otherwise, you won't make it back to the original layer when you release the key (and you'll get a keycode sent). You can only switch to layers *above* your current layer. If you're on layer 0 and you use `MO(1)`, that will switch to layer 1 just fine. But if you include `MO(3)` on layer 5, that won't do anything for you -- because layer 3 is lower than layer 5 on the stack.
|
||||
|
||||
`LT(layer, kc)` - momentary switch to *layer* when held, and *kc* when tapped. Like `MO()`, this only works upwards in the layer stack (`layer` must be higher than the current layer).
|
||||
|
||||
`TG(layer)` - toggles a layer on or off. As with `MO()`, you should set this key as `KC_TRNS` in the destination layer so that tapping it again actually toggles back to the original layer. Only works upwards in the layer stack.
|
||||
|
||||
### Fun with modifier keys
|
||||
|
||||
* `LSFT(kc)` - applies left Shift to *kc* (keycode) - `S(kc)` is an alias
|
||||
* `RSFT(kc)` - applies right Shift to *kc*
|
||||
* `LCTL(kc)` - applies left Control to *kc*
|
||||
* `RCTL(kc)` - applies right Control to *kc*
|
||||
* `LALT(kc)` - applies left Alt to *kc*
|
||||
* `RALT(kc)` - applies right Alt to *kc*
|
||||
* `LGUI(kc)` - applies left GUI (command/win) to *kc*
|
||||
* `RGUI(kc)` - applies right GUI (command/win) to *kc*
|
||||
|
||||
You can also chain these, like this:
|
||||
|
||||
LALT(LCTL(KC_DEL)) -- this makes a key that sends Alt, Control, and Delete in a single keypress.
|
||||
|
||||
The following shortcuts automatically add `LSFT()` to keycodes to get commonly used symbols. Their long names are also available and documented in `/quantum/keymap_common.h`.
|
||||
|
||||
KC_TILD ~
|
||||
KC_EXLM !
|
||||
KC_AT @
|
||||
KC_HASH #
|
||||
KC_DLR $
|
||||
KC_PERC %
|
||||
KC_CIRC ^
|
||||
KC_AMPR &
|
||||
KC_ASTR *
|
||||
KC_LPRN (
|
||||
KC_RPRN )
|
||||
KC_UNDS _
|
||||
KC_PLUS +
|
||||
KC_LCBR {
|
||||
KC_RCBR }
|
||||
KC_PIPE |
|
||||
KC_COLN :
|
||||
|
||||
`MT(mod, kc)` - is *mod* (modifier key - MOD_LCTL, MOD_LSFT) when held, and *kc* when tapped. In other words, you can have a key that sends Esc (or the letter O or whatever) when you tap it, but works as a Control key or a Shift key when you hold it down.
|
||||
|
||||
These are the values you can use for the `mod` in `MT()` (right-hand modifiers are not available):
|
||||
|
||||
* MOD_LCTL
|
||||
* MOD_LSFT
|
||||
* MOD_LALT
|
||||
* MOD_LGUI
|
||||
|
||||
These can also be combined like `MOD_LCTL | MOD_LSFT` e.g. `MT(MOD_LCTL | MOD_LSFT, KC_ESC)` which would activate Control and Shift when held, and send Escape when tapped.
|
||||
|
||||
We've added shortcuts to make common modifier/tap (mod-tap) mappings more compact:
|
||||
|
||||
* `CTL_T(kc)` - is LCTL when held and *kc* when tapped
|
||||
* `SFT_T(kc)` - is LSFT when held and *kc* when tapped
|
||||
* `ALT_T(kc)` - is LALT when held and *kc* when tapped
|
||||
* `GUI_T(kc)` - is LGUI when held and *kc* when tapped
|
||||
* `ALL_T(kc)` - is Hyper (all mods) when held and *kc* when tapped. To read more about what you can do with a Hyper key, see [this blog post by Brett Terpstra](http://brettterpstra.com/2012/12/08/a-useful-caps-lock-key/)
|
||||
|
||||
### Temporarily setting the default layer
|
||||
|
||||
`DF(layer)` - sets default layer to *layer*. The default layer is the one at the "bottom" of the layer stack - the ultimate fallback layer. This currently does not persist over power loss. When you plug the keyboard back in, layer 0 will always be the default. It is theoretically possible to work around that, but that's not what `DF` does.
|
||||
|
||||
### Remember: These are just aliases
|
||||
|
||||
These functions work the same way that their `ACTION_*` functions do - they're just quick aliases. To dig into all of the tmk ACTION_* functions, please see the [TMK documentation](https://github.com/jackhumbert/qmk_firmware/blob/master/tmk_core/doc/keymap.md#2-action).
|
||||
|
||||
Instead of using `FNx` when defining `ACTION_*` functions, you can use `F(x)` - the benefit here is being able to use more than 32 function actions (up to 4096), if you happen to need them.
|
||||
|
||||
## Macro shortcuts: Send a whole string when pressing just one key
|
||||
|
||||
Instead of using the `ACTION_MACRO` function, you can simply use `M(n)` to access macro *n* - *n* will get passed into the `action_get_macro` as the `id`, and you can use a switch statement to trigger it. This gets called on the keydown and keyup, so you'll need to use an if statement testing `record->event.pressed` (see keymap_default.c).
|
||||
|
||||
```c
|
||||
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) // this is the function signature -- just copy/paste it into your keymap file as it is.
|
||||
{
|
||||
switch(id) {
|
||||
case 0: // this would trigger when you hit a key mapped as M(0)
|
||||
if (record->event.pressed) {
|
||||
return MACRO( I(255), T(H), T(E), T(L), T(L), W(255), T(O), END ); // this sends the string 'hello' when the macro executes
|
||||
}
|
||||
break;
|
||||
}
|
||||
return MACRO_NONE;
|
||||
};
|
||||
```
|
||||
A macro can include the following commands:
|
||||
|
||||
* I() change interval of stroke in milliseconds.
|
||||
* D() press key.
|
||||
* U() release key.
|
||||
* T() type key(press and release).
|
||||
* W() wait (milliseconds).
|
||||
* END end mark.
|
||||
|
||||
So above you can see the stroke interval changed to 255ms between each keystroke, then a bunch of keys being typed, waits a while, then the macro ends.
|
||||
|
||||
Note: Using macros to have your keyboard send passwords for you is a bad idea.
|
||||
|
||||
### Additional keycode aliases for software-implemented layouts (Colemak, Dvorak, etc)
|
||||
|
||||
Everything is assuming you're in Qwerty (in software) by default, but there is built-in support for using a Colemak or Dvorak layout by including this at the top of your keymap:
|
||||
|
||||
#include "keymap_<layout>.h"
|
||||
|
||||
Where <layout> is "colemak" or "dvorak". After including this line, you will get access to:
|
||||
|
||||
* `CM_*` for all of the Colemak-equivalent characters
|
||||
* `DV_*` for all of the Dvorak-equivalent characters
|
||||
|
||||
These implementations assume you're using Colemak or Dvorak on your OS, not on your keyboard - this is referred to as a software-implemented layout. If your computer is in Qwerty and your keymap is in Colemak or Dvorak, this is referred to as a firmware-implemented layout, and you won't need these features.
|
||||
|
||||
To give an example, if you're using software-implemented Colemak, and want to get an `F`, you would use `CM_F` - `KC_F` under these same circumstances would result in `T`.
|
||||
|
||||
## Additional language support
|
||||
|
||||
In `quantum/keymap_extras/`, you'll see various language files - these work the same way as the alternative layout ones do. Most are defined by their two letter country/language code followed by an underscore and a 4-letter abbreviation of its name. `FR_UGRV` which will result in a `ù` when using a software-implemented AZERTY layout. It's currently difficult to send such characters in just the firmware (but it's being worked on - see Unicode support).
|
||||
|
||||
## Unicode support
|
||||
|
||||
You can currently send 4 hex digits with your OS-specific modifier key (RALT for OSX with the "Unicode Hex Input" layout) - this is currently limited to supporting one OS at a time, and requires a recompile for switching. 8 digit hex codes are being worked on. The keycode function is `UC(n)`, where *n* is a 4 digit hexidecimal. Enable from the Makefile.
|
||||
|
||||
## Other firmware shortcut keycodes
|
||||
|
||||
* `RESET` - puts the MCU in DFU mode for flashing new firmware (with `make dfu`)
|
||||
* `DEBUG` - the firmware into debug mode - you'll need hid_listen to see things
|
||||
* `BL_ON` - turns the backlight on
|
||||
* `BL_OFF` - turns the backlight off
|
||||
* `BL_<n>` - sets the backlight to level *n*
|
||||
* `BL_INC` - increments the backlight level by one
|
||||
* `BL_DEC` - decrements the backlight level by one
|
||||
* `BL_TOGG` - toggles the backlight
|
||||
* `BL_STEP` - steps through the backlight levels
|
||||
|
||||
Enable the backlight from the Makefile.
|
||||
|
||||
## MIDI functionalty
|
||||
|
||||
This is still a WIP, but check out `quantum/keymap_midi.c` to see what's happening. Enable from the Makefile.
|
||||
|
||||
## Bluetooth functionality
|
||||
|
||||
This requires [some hardware changes](https://www.reddit.com/r/MechanicalKeyboards/comments/3psx0q/the_planck_keyboard_with_bluetooth_guide_and/?ref=search_posts), but can be enabled via the Makefile. The firmware will still output characters via USB, so be aware of this when charging via a computer. It would make sense to have a switch on the Bluefruit to turn it off at will.
|
||||
|
||||
## Building
|
||||
|
||||
Download or clone the whole firmware and navigate to the keyboard/planck folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button.
|
||||
|
||||
Depending on which keymap you would like to use, you will have to compile slightly differently.
|
||||
|
||||
### Default
|
||||
To build with the default keymap, simply run `make`.
|
||||
|
||||
### Other Keymaps
|
||||
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document (you can find in top README.md) and existent keymap files.
|
||||
|
||||
To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
|
||||
```
|
||||
$ make KEYMAP=[default|jack|<name>]
|
||||
```
|
||||
Keymaps follow the format **__keymap\_\<name\>.c__** and are stored in the `keymaps` folder.
|
||||
|
|
@ -0,0 +1,29 @@
|
|||
#include "atreus.h"
|
||||
|
||||
__attribute__ ((weak))
|
||||
void * matrix_init_user(void) {
|
||||
// leave these blank
|
||||
};
|
||||
|
||||
__attribute__ ((weak))
|
||||
void * matrix_scan_user(void) {
|
||||
// leave these blank
|
||||
};
|
||||
|
||||
void * matrix_init_kb(void) {
|
||||
// put your keyboard start-up code here
|
||||
// runs once when the firmware starts up
|
||||
|
||||
if (matrix_init_user) {
|
||||
(*matrix_init_user)();
|
||||
}
|
||||
};
|
||||
|
||||
void * matrix_scan_kb(void) {
|
||||
// put your looping keyboard code here
|
||||
// runs every cycle (a lot)
|
||||
|
||||
if (matrix_scan_user) {
|
||||
(*matrix_scan_user)();
|
||||
}
|
||||
};
|
||||
|
|
@ -0,0 +1,29 @@
|
|||
#ifndef ATREUS_H
|
||||
#define ATREUS_H
|
||||
|
||||
#include "matrix.h"
|
||||
#include "keymap_common.h"
|
||||
#include "backlight.h"
|
||||
#include <stddef.h>
|
||||
|
||||
// This a shortcut to help you visually see your layout.
|
||||
// The following is an example using the Planck MIT layout
|
||||
// The first section contains all of the arguements
|
||||
// The second converts the arguments into a two-dimensional array
|
||||
#define KEYMAP( \
|
||||
k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \
|
||||
k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \
|
||||
k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \
|
||||
k30, k31, k32, k33, k34, k35, k37, k38, k39, k3a, k3b \
|
||||
) \
|
||||
{ \
|
||||
{ k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \
|
||||
{ k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \
|
||||
{ k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \
|
||||
{ k30, k31, k32, k33, k34, k35, k35, k37, k38, k39, k3a, k3b } \
|
||||
}
|
||||
|
||||
void * matrix_init_user(void);
|
||||
void * matrix_scan_user(void);
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,82 @@
|
|||
/*
|
||||
Copyright 2012 Jun Wako <wakojun@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#include "config_common.h"
|
||||
|
||||
/* USB Device descriptor parameter */
|
||||
|
||||
#define VENDOR_ID 0xFEED
|
||||
#define PRODUCT_ID 0x6060
|
||||
#define DEVICE_VER 0x0001
|
||||
#define MANUFACTURER Technomancy
|
||||
#define PRODUCT Atreus
|
||||
#define DESCRIPTION q.m.k. keyboard firmware for Atreus
|
||||
|
||||
/* key matrix size */
|
||||
#define MATRIX_ROWS 4
|
||||
#define MATRIX_COLS 11
|
||||
|
||||
// Planck PCB default pin-out
|
||||
// Change this to how you wired your keyboard
|
||||
// COLS: Left to right, ROWS: Top to bottom
|
||||
#define COLS (int []){ F6, F5, F4, B7, B6, B5, B4, B3, B2, B1, B0}
|
||||
#define ROWS (int []){ D0, D1, D2, D3 }
|
||||
|
||||
/* COL2ROW or ROW2COL */
|
||||
#define DIODE_DIRECTION COL2ROW
|
||||
|
||||
/* define if matrix has ghost */
|
||||
//#define MATRIX_HAS_GHOST
|
||||
|
||||
/* number of backlight levels */
|
||||
//#define BACKLIGHT_LEVELS 3
|
||||
|
||||
/* Set 0 if debouncing isn't needed */
|
||||
#define DEBOUNCE 5
|
||||
|
||||
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
|
||||
#define LOCKING_SUPPORT_ENABLE
|
||||
/* Locking resynchronize hack */
|
||||
#define LOCKING_RESYNC_ENABLE
|
||||
|
||||
/* key combination for command */
|
||||
#define IS_COMMAND() ( \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
|
||||
)
|
||||
|
||||
/*
|
||||
* Feature disable options
|
||||
* These options are also useful to firmware size reduction.
|
||||
*/
|
||||
|
||||
/* disable debug print */
|
||||
//#define NO_DEBUG
|
||||
|
||||
/* disable print */
|
||||
//#define NO_PRINT
|
||||
|
||||
/* disable action features */
|
||||
//#define NO_ACTION_LAYER
|
||||
//#define NO_ACTION_TAPPING
|
||||
//#define NO_ACTION_ONESHOT
|
||||
//#define NO_ACTION_MACRO
|
||||
//#define NO_ACTION_FUNCTION
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,51 @@
|
|||
// this is the style you want to emulate.
|
||||
// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
|
||||
|
||||
#include "atreus.h"
|
||||
|
||||
// Each layer gets a name for readability, which is then used in the keymap matrix below.
|
||||
// The underscores don't mean anything - you can have a layer called STUFF or any other name.
|
||||
// Layer names don't all need to be of the same length, obviously, and you can also skip them
|
||||
// entirely and just use numbers.
|
||||
#define _QW 0
|
||||
#define _RS 1
|
||||
#define _LW 2
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
[_QW] = { /* Qwerty */
|
||||
{KC_Q, KC_W, KC_E, KC_R, KC_T, KC_TRNS, KC_Y, KC_U, KC_I, KC_O, KC_P },
|
||||
{KC_A, KC_S, KC_D, KC_F, KC_G, KC_TRNS, KC_H, KC_J, KC_K, KC_L, KC_SCLN },
|
||||
{KC_Z, KC_X, KC_C, KC_V, KC_B, KC_LALT, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH },
|
||||
{KC_ESC, KC_TAB, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, MO(_RS), KC_MINS, KC_QUOT, KC_ENT }
|
||||
},
|
||||
[_RS] = { /* [> RAISE <] */
|
||||
{KC_EXLM, KC_AT, KC_LCBR, KC_RCBR, KC_PIPE, KC_TRNS, KC_PGUP, KC_7, KC_8, KC_9, KC_ASTR},
|
||||
{KC_HASH, KC_DLR, KC_LPRN, KC_RPRN, KC_GRV, KC_TRNS, KC_PGDN, KC_4, KC_5, KC_6, KC_PLUS},
|
||||
{KC_PERC, KC_CIRC, KC_LBRC, KC_RBRC, KC_TILD, KC_LALT, KC_AMPR, KC_1, KC_2, KC_3, KC_BSLS},
|
||||
{TG(_LW), KC_INS, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, KC_TRNS, KC_DOT, KC_0, KC_EQL}
|
||||
},
|
||||
[_LW] = { /* [> LOWER <] */
|
||||
{KC_INS, KC_HOME, KC_UP, KC_END, KC_PGUP, KC_TRNS, KC_UP, KC_F7, KC_F8, KC_F9, KC_F10},
|
||||
{KC_DELT, KC_LEFT, KC_DOWN, KC_RGHT, KC_DOWN, KC_TRNS, KC_DOWN, KC_F4, KC_F5, KC_F6, KC_F11},
|
||||
{KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_LALT, KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F12},
|
||||
{KC_TRNS, KC_TRNS, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, DF(_QW), KC_TRNS, KC_TRNS, RESET}
|
||||
}};
|
||||
|
||||
const uint16_t PROGMEM fn_actions[] = {
|
||||
|
||||
};
|
||||
|
||||
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
|
||||
{
|
||||
// MACRODOWN only works in this function
|
||||
switch(id) {
|
||||
case 0:
|
||||
if (record->event.pressed) {
|
||||
register_code(KC_RSFT);
|
||||
} else {
|
||||
unregister_code(KC_RSFT);
|
||||
}
|
||||
break;
|
||||
}
|
||||
return MACRO_NONE;
|
||||
};
|
||||
Loading…
Reference in New Issue