[Keyboard] Add support for db63 hotswap rbg (#7771)

* correct the matrix pin for db63

* first correct layout

* adding RGB support for db63

* adding backlighting keycode

* enable back extension

* update readme for the bootloader

* correct the capslock pin

* update correct info.json and layout following suggestion

* editing contact

* Update keyboards/db/db63/README.md

Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com>

* Update keyboards/db/db63/README.md

Co-Authored-By: James Young <18669334+noroadsleft@users.noreply.github.com>

Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
master
Hung DO 2020-01-05 08:04:49 +07:00 committed by Drashna Jaelre
parent d4b15cd93a
commit 59c783df48
8 changed files with 614 additions and 0 deletions

View File

@ -0,0 +1,21 @@
# DB63
A 65% keyboard hotswap with RGB that runs ps2avrgb natively, with USB C, RGB underglow and backlight.
* Keyboard Maintainer: QMK Community
* Hardware Supported: DB63 (ATmega32A)
* [Keyboard layout](http://www.keyboard-layout-editor.com/#/gists/dadea703fc8bfc87dc7c480de9f3ef38)
Make example for this keyboard (after setting up your build environment):
make db/db63:default
Flashing example for this keyboard ([after setting up the bootloadHID flashing environment](https://docs.qmk.fm/#/flashing_bootloadhid))
make db/db63:default:flash
**Reset Key**: Hold down the key located at *K00*, commonly programmed as *Escape* while plugging in the keyboard. (*All backlight LEDs will flash which indicate the board is in bootloader mode.*)
**Tips**: Another trick to enable the board in reset mode is using BootMapper Client->Options->Set Bootloader. (*This is only available for the first time, before flashing QMK Firmware.*)
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

View File

@ -0,0 +1,42 @@
/*
Copyright 2020 Hung DO <hungdohuy@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#pragma once
#define VENDOR_ID 0xFAAD
#define PRODUCT_ID 0x422D
#define DEVICE_VER 0x0200
// You can edit those at usbconfig.h about line 250. These values will
// unforunatly be ignored so far
#define MANUFACTURER HNB
#define PRODUCT DB63v1 Hotswap
#define MATRIX_ROWS 6
#define MATRIX_COLS 14
#define MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5 }
#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
#define UNUSED_PINS
#define RGBLED_NUM 18
#define RGBLIGHT_ANIMATIONS
#define NO_UART 1
#define BACKLIGHT_PIN D4
#define BACKLIGHT_LEVELS 3

View File

@ -0,0 +1,17 @@
/* Copyright 2019 MechMerlin
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include "db63.h"

View File

@ -0,0 +1,49 @@
/*
Copyright 2020 Hung DO <hungdohuy@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#pragma once
#include "quantum.h"
#define _x_ KC_NO
/* This a shortcut to help you visually see your layout.
*
* The first section contains all of the arguments representing the physical
* layout of the board and position of the keys.
*
* The second converts the arguments into a two-dimensional array which
* represents the switch matrix.
* MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5 }
* MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
*
*/
#define LAYOUT( \
k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, \
k10 , k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \
k20 , k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \
k30 , k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, \
k40 , k41 , k42 , k43 , k44, k45, k46, k47 , k48 \
) { \
{ k00, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_ }, \
{ _x_, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d }, \
{ k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d }, \
{ k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k46 }, \
{ k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3c, k3a, k47, _x_ }, \
{ k40, k41, k42, k43, k45, _x_, _x_, k44, _x_, _x_, _x_, k3b, _x_, k48 } \
}

View File

@ -0,0 +1,18 @@
{
"keyboard_name": "db63",
"url": "http://www.keyboard-layout-editor.com/#/gists/dadea703fc8bfc87dc7c480de9f3ef38",
"maintainer": "QMK Community",
"width": 15,
"height": 5,
"layouts": {
"LAYOUT": {
"layout": [
{ "label": "~", "x": 0, "y": 0 }, { "label": "!", "x": 1, "y": 0 }, { "label": "@", "x": 2, "y": 0 }, { "label": "#", "x": 3, "y": 0 }, { "label": "$", "x": 4, "y": 0 }, { "label": "%", "x": 5, "y": 0 }, { "label": "^", "x": 6, "y": 0 }, { "label": "&", "x": 7, "y": 0 }, { "label": "*", "x": 8, "y": 0 }, { "label": "(", "x": 9, "y": 0 }, { "label": ")", "x": 10, "y": 0 }, { "label": "_", "x": 11, "y": 0 }, { "label": "+", "x": 12, "y": 0 }, { "label": "Backspace", "x": 13, "y": 0, "w": 2 },
{ "label": "Tab", "x": 0, "y": 1, "w": 1.5 }, { "label": "Q", "x": 1.5, "y": 1 }, { "label": "W", "x": 2.5, "y": 1 }, { "label": "E", "x": 3.5, "y": 1 }, { "label": "R", "x": 4.5, "y": 1 }, { "label": "T", "x": 5.5, "y": 1 }, { "label": "Y", "x": 6.5, "y": 1 }, { "label": "U", "x": 7.5, "y": 1 }, { "label": "I", "x": 8.5, "y": 1 }, { "label": "O", "x": 9.5, "y": 1 }, { "label": "P", "x": 10.5, "y": 1 }, { "label": "{", "x": 11.5, "y": 1 }, { "label": "}", "x": 12.5, "y": 1 }, { "label": "|", "x": 13.5, "y": 1, "w": 1.5 },
{ "label": "Fn3", "x": 0, "y": 2, "w": 1.75 }, { "label": "A", "x": 1.75, "y": 2 }, { "label": "S", "x": 2.75, "y": 2 }, { "label": "D", "x": 3.75, "y": 2 }, { "label": "F", "x": 4.75, "y": 2 }, { "label": "G", "x": 5.75, "y": 2 }, { "label": "H", "x": 6.75, "y": 2 }, { "label": "J", "x": 7.75, "y": 2 }, { "label": "K", "x": 8.75, "y": 2 }, { "label": "L", "x": 9.75, "y": 2 }, { "label": ":", "x": 10.75, "y": 2 }, { "label": "\"", "x": 11.75, "y": 2 }, { "label": "Enter", "x": 12.75, "y": 2, "w": 2.25 },
{ "label": "Shift", "x": 0, "y": 3, "w": 2.25 }, { "label": "Z", "x": 2.25, "y": 3 }, { "label": "X", "x": 3.25, "y": 3 }, { "label": "C", "x": 4.25, "y": 3 }, { "label": "V", "x": 5.25, "y": 3 }, { "label": "B", "x": 6.25, "y": 3 }, { "label": "N", "x": 7.25, "y": 3 }, { "label": "M", "x": 8.25, "y": 3 }, { "label": "<", "x": 9.25, "y": 3 }, { "label": ">", "x": 10.25, "y": 3 }, { "label": "Shift", "x": 11.25, "y": 3, "w": 1.75 }, { "label": "Up", "x": 13, "y": 3 }, { "label": "Fn2", "x": 14, "y": 3 },
{ "label": "Ctrl", "x": 0, "y": 4, "w": 1.25 }, { "label": "Alt", "x": 1.25, "y": 4, "w": 1.25 }, { "label": "Win", "x": 2.5, "y": 4, "w": 1.25 }, { "label": "Space", "x": 3.75, "y": 4, "w": 6.25 }, { "label": "?", "x": 10, "y": 4 }, { "label": "Fn1", "x": 11, "y": 4 }, { "label": "Left", "x": 12, "y": 4 }, { "label": "Down", "x": 13, "y": 4 }, { "label": "Right", "x": 14, "y": 4 }
]
}
}
}

View File

@ -0,0 +1,60 @@
/*
Copyright 2020 Hung DO <hungdohuy@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include QMK_KEYBOARD_H
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[0] = LAYOUT(
KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC,
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
MO(3), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT,
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, MO(2),
KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_SLSH, MO(1), KC_LEFT, KC_DOWN, KC_RGHT
),
[1] = LAYOUT(
KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC,
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, _______,
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, XXXXXXX,
KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, MO(1), KC_LEFT, KC_DOWN, KC_RGHT
),
[2] = LAYOUT(
KC_GESC, RGB_M_P, RGB_M_B, RGB_M_R, RGB_M_SW, RGB_M_SN, RGB_M_K, RGB_M_X, RGB_M_G, RGB_M_T, RGB_TOG, RGB_VAD, RGB_VAI, KC_BSPC,
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
XXXXXXX, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, _______,
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, MO(2),
KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT
),
[3] = LAYOUT(
_______, _______, _______, _______, _______, _______, _______, _______, BL_STEP, BL_BRTG, BL_TOGG, BL_DEC, BL_INC, _______,
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
MO(3), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, RESET,
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, XXXXXXX,
KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT
),
};
bool led_update_user(led_t led_state) {
if (led_state.caps_lock) {
rgblight_sethsv(HSV_CYAN);
writePinHigh(D1);
} else {
rgblight_sethsv(HSV_GREEN);
writePinLow(D1);
}
return false;
}

View File

@ -0,0 +1,24 @@
# MCU name
MCU = atmega32a
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = bootloadHID
# build options
BOOTMAGIC_ENABLE = no
MOUSEKEY_ENABLE = yes
EXTRAKEY_ENABLE = yes
CONSOLE_ENABLE = no
COMMAND_ENABLE = yes
BACKLIGHT_ENABLE = yes
RGBLIGHT_ENABLE = yes
WS2812_DRIVER = i2c
OPT_DEFS = -DDEBUG_LEVEL=0

View File

@ -0,0 +1,383 @@
/* Name: usbconfig.h
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
* Author: Christian Starkjohann
* Creation Date: 2005-04-01
* Tabsize: 4
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
*/
#pragma once
#include "config.h"
/*
General Description:
This file is an example configuration (with inline documentation) for the USB
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
other hardware interrupt, as long as it is the highest level interrupt, see
section at the end of this file).
*/
/* ---------------------------- Hardware Config ---------------------------- */
#define USB_CFG_IOPORTNAME D
/* This is the port where the USB bus is connected. When you configure it to
* "B", the registers PORTB, PINB and DDRB will be used.
*/
#define USB_CFG_DMINUS_BIT 3
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
* This may be any bit in the port.
*/
#define USB_CFG_DPLUS_BIT 2
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
* This may be any bit in the port. Please note that D+ must also be connected
* to interrupt pin INT0! [You can also use other interrupts, see section
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
* markers every millisecond.]
*/
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
* require no crystal, they tolerate +/- 1% deviation from the nominal
* frequency. All other rates require a precision of 2000 ppm and thus a
* crystal!
* Since F_CPU should be defined to your actual clock rate anyway, you should
* not need to modify this setting.
*/
#define USB_CFG_CHECK_CRC 0
/* Define this to 1 if you want that the driver checks integrity of incoming
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
* currently only available for 18 MHz crystal clock. You must choose
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
*/
/* ----------------------- Optional Hardware Config ------------------------ */
/* #define USB_CFG_PULLUP_IOPORTNAME D */
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
* V+, you can connect and disconnect the device from firmware by calling
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
* This constant defines the port on which the pullup resistor is connected.
*/
/* #define USB_CFG_PULLUP_BIT 4 */
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
* above) where the 1.5k pullup resistor is connected. See description
* above for details.
*/
/* --------------------------- Functional Range ---------------------------- */
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
/* Define this to 1 if you want to compile a version with two endpoints: The
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
* number).
*/
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
/* Define this to 1 if you want to compile a version with three endpoints: The
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
* configured below) and a catch-all default interrupt-in endpoint as above.
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
*/
#define USB_CFG_EP3_NUMBER 3
/* If the so-called endpoint 3 is used, it can now be configured to any other
* endpoint number (except 0) with this macro. Default if undefined is 3.
*/
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
/* The above macro defines the startup condition for data toggling on the
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
* Since the token is toggled BEFORE sending any data, the first packet is
* sent with the oposite value of this configuration!
*/
#define USB_CFG_IMPLEMENT_HALT 0
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
* it is required by the standard. We have made it a config option because it
* bloats the code considerably.
*/
#define USB_CFG_SUPPRESS_INTR_CODE 0
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
* want to send any data over them. If this macro is defined to 1, functions
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
* you need the interrupt-in endpoints in order to comply to an interface
* (e.g. HID), but never want to send any data. This option saves a couple
* of bytes in flash memory and the transmit buffers in RAM.
*/
#define USB_CFG_IS_SELF_POWERED 0
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
* device is powered from the USB bus.
*/
#define USB_CFG_IMPLEMENT_FN_WRITE 1
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
* transfers. Set it to 0 if you don't need it and want to save a couple of
* bytes.
*/
#define USB_CFG_IMPLEMENT_FN_READ 0
/* Set this to 1 if you need to send control replies which are generated
* "on the fly" when usbFunctionRead() is called. If you only want to send
* data from a static buffer, set it to 0 and return the data from
* usbFunctionSetup(). This saves a couple of bytes.
*/
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
* You must implement the function usbFunctionWriteOut() which receives all
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
* can be found in 'usbRxToken'.
*/
#define USB_CFG_HAVE_FLOWCONTROL 0
/* Define this to 1 if you want flowcontrol over USB data. See the definition
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
* usbdrv.h.
*/
#define USB_CFG_DRIVER_FLASH_PAGE 0
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
* where the driver's constants (descriptors) are located. Or in other words:
* Define this to 1 for boot loaders on the ATMega128.
*/
#define USB_CFG_LONG_TRANSFERS 0
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
* in a single control-in or control-out transfer. Note that the capability
* for long transfers increases the driver size.
*/
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
/* This macro is a hook if you want to do unconventional things. If it is
* defined, it's inserted at the beginning of received message processing.
* If you eat the received message and don't want default processing to
* proceed, do a return after doing your things. One possible application
* (besides debugging) is to flash a status LED on each packet.
*/
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
/* This macro is a hook if you need to know when an USB RESET occurs. It has
* one parameter which distinguishes between the start of RESET state and its
* end.
*/
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
* received.
*/
#define USB_COUNT_SOF 1
/* define this macro to 1 if you need the global variable "usbSofCount" which
* counts SOF packets. This feature requires that the hardware interrupt is
* connected to D- instead of D+.
*/
/* #ifdef __ASSEMBLER__
* macro myAssemblerMacro
* in YL, TCNT0
* sts timer0Snapshot, YL
* endm
* #endif
* #define USB_SOF_HOOK myAssemblerMacro
* This macro (if defined) is executed in the assembler module when a
* Start Of Frame condition is detected. It is recommended to define it to
* the name of an assembler macro which is defined here as well so that more
* than one assembler instruction can be used. The macro may use the register
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
* immediately after an SOF pulse may be lost and must be retried by the host.
* What can you do with this hook? Since the SOF signal occurs exactly every
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
* designs running on the internal RC oscillator.
* Please note that Start Of Frame detection works only if D- is wired to the
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
*/
#define USB_CFG_CHECK_DATA_TOGGLING 0
/* define this macro to 1 if you want to filter out duplicate data packets
* sent by the host. Duplicates occur only as a consequence of communication
* errors, when the host does not receive an ACK. Please note that you need to
* implement the filtering yourself in usbFunctionWriteOut() and
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
* for each control- and out-endpoint to check for duplicate packets.
*/
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
/* define this macro to 1 if you want the function usbMeasureFrameLength()
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
*/
#define USB_USE_FAST_CRC 0
/* The assembler module has two implementations for the CRC algorithm. One is
* faster, the other is smaller. This CRC routine is only used for transmitted
* messages where timing is not critical. The faster routine needs 31 cycles
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
* may be worth the 32 bytes bigger code size if you transmit lots of data and
* run the AVR close to its limit.
*/
/* -------------------------- Device Description --------------------------- */
#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
/* USB vendor ID for the device, low byte first. If you have registered your
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
* *** IMPORTANT NOTE ***
* This template uses obdev's shared VID/PID pair for Vendor Class devices
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
* the implications!
*/
#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
/* This is the ID of the product, low byte first. It is interpreted in the
* scope of the vendor ID. If you have registered your own VID with usb.org
* or if you have licensed a PID from somebody else, define it here. Otherwise
* you may use one of obdev's free shared VID/PID pairs. See the file
* USB-IDs-for-free.txt for details!
* *** IMPORTANT NOTE ***
* This template uses obdev's shared VID/PID pair for Vendor Class devices
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
* the implications!
*/
#define USB_CFG_DEVICE_VERSION (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
/* Version number of the device: Minor number first, then major number.
*/
#define USB_CFG_VENDOR_NAME 'H', 'N', 'B'
#define USB_CFG_VENDOR_NAME_LEN 3
/* These two values define the vendor name returned by the USB device. The name
* must be given as a list of characters under single quotes. The characters
* are interpreted as Unicode (UTF-16) entities.
* If you don't want a vendor name string, undefine these macros.
* ALWAYS define a vendor name containing your Internet domain name if you use
* obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
* details.
*/
#define USB_CFG_DEVICE_NAME 'D', 'B', '6', '3', 'H', 'S'
#define USB_CFG_DEVICE_NAME_LEN 6
/* Same as above for the device name. If you don't want a device name, undefine
* the macros. See the file USB-IDs-for-free.txt before you assign a name if
* you use a shared VID/PID.
*/
/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
/* Same as above for the serial number. If you don't want a serial number,
* undefine the macros.
* It may be useful to provide the serial number through other means than at
* compile time. See the section about descriptor properties below for how
* to fine tune control over USB descriptors such as the string descriptor
* for the serial number.
*/
#define USB_CFG_DEVICE_CLASS 0
#define USB_CFG_DEVICE_SUBCLASS 0
/* See USB specification if you want to conform to an existing device class.
* Class 0xff is "vendor specific".
*/
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
/* See USB specification if you want to conform to an existing device class or
* protocol. The following classes must be set at interface level:
* HID class is 3, no subclass and protocol required (but may be useful!)
* CDC class is 2, use subclass 2 and protocol 1 for ACM
*/
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
/* Define this to the length of the HID report descriptor, if you implement
* an HID device. Otherwise don't define it or define it to 0.
* If you use this define, you must add a PROGMEM character array named
* "usbHidReportDescriptor" to your code which contains the report descriptor.
* Don't forget to keep the array and this define in sync!
*/
/* #define USB_PUBLIC static */
/* Use the define above if you #include usbdrv.c instead of linking against it.
* This technique saves a couple of bytes in flash memory.
*/
/* ------------------- Fine Control over USB Descriptors ------------------- */
/* If you don't want to use the driver's default USB descriptors, you can
* provide our own. These can be provided as (1) fixed length static data in
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
* information about this function.
* Descriptor handling is configured through the descriptor's properties. If
* no properties are defined or if they are 0, the default descriptor is used.
* Possible properties are:
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
* you want RAM pointers.
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
* in static memory is in RAM, not in flash memory.
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
* the driver must know the descriptor's length. The descriptor itself is
* found at the address of a well known identifier (see below).
* List of static descriptor names (must be declared PROGMEM if in flash):
* char usbDescriptorDevice[];
* char usbDescriptorConfiguration[];
* char usbDescriptorHidReport[];
* char usbDescriptorString0[];
* int usbDescriptorStringVendor[];
* int usbDescriptorStringDevice[];
* int usbDescriptorStringSerialNumber[];
* Other descriptors can't be provided statically, they must be provided
* dynamically at runtime.
*
* Descriptor properties are or-ed or added together, e.g.:
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
*
* The following descriptors are defined:
* USB_CFG_DESCR_PROPS_DEVICE
* USB_CFG_DESCR_PROPS_CONFIGURATION
* USB_CFG_DESCR_PROPS_STRINGS
* USB_CFG_DESCR_PROPS_STRING_0
* USB_CFG_DESCR_PROPS_STRING_VENDOR
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
* USB_CFG_DESCR_PROPS_HID
* USB_CFG_DESCR_PROPS_HID_REPORT
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
*
* Note about string descriptors: String descriptors are not just strings, they
* are Unicode strings prefixed with a 2 byte header. Example:
* int serialNumberDescriptor[] = {
* USB_STRING_DESCRIPTOR_HEADER(6),
* 'S', 'e', 'r', 'i', 'a', 'l'
* };
*/
#define USB_CFG_DESCR_PROPS_DEVICE 0
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
#define USB_CFG_DESCR_PROPS_STRINGS 0
#define USB_CFG_DESCR_PROPS_STRING_0 0
#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
//#define USB_CFG_DESCR_PROPS_HID 0
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
//#define USB_CFG_DESCR_PROPS_HID_REPORT 0
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
#define usbMsgPtr_t unsigned short
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
* a scalar type here because gcc generates slightly shorter code for scalar
* arithmetics than for pointer arithmetics. Remove this define for backward
* type compatibility or define it to an 8 bit type if you use data in RAM only
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
*/
/* ----------------------- Optional MCU Description ------------------------ */
/* The following configurations have working defaults in usbdrv.h. You
* usually don't need to set them explicitly. Only if you want to run
* the driver on a device which is not yet supported or with a compiler
* which is not fully supported (such as IAR C) or if you use a differnt
* interrupt than INT0, you may have to define some of these.
*/
/* #define USB_INTR_CFG MCUCR */
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
/* #define USB_INTR_CFG_CLR 0 */
/* #define USB_INTR_ENABLE GIMSK */
/* #define USB_INTR_ENABLE_BIT INT0 */
/* #define USB_INTR_PENDING GIFR */
/* #define USB_INTR_PENDING_BIT INTF0 */
/* #define USB_INTR_VECTOR INT0_vect */
/* Set INT1 for D- falling edge to count SOF */
/* #define USB_INTR_CFG EICRA */
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
/* #define USB_INTR_CFG_CLR 0 */
/* #define USB_INTR_ENABLE EIMSK */
#define USB_INTR_ENABLE_BIT INT1
/* #define USB_INTR_PENDING EIFR */
#define USB_INTR_PENDING_BIT INTF1
#define USB_INTR_VECTOR INT1_vect