remove orphaned clueboard files

master
Seth Chandler 2016-08-05 23:19:12 -04:00
parent 213cb2c243
commit 545925fb1b
2 changed files with 0 additions and 134 deletions

View File

@ -1,71 +0,0 @@
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality (+4870)
BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150)
MIDI_ENABLE ?= no # MIDI controls
AUDIO_ENABLE ?= no
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
ifndef QUANTUM_DIR
include ../../Makefile
endif

View File

@ -1,63 +0,0 @@
#include "clueboard2.h"
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
matrix_init_user();
led_init_ports();
// JTAG disable for PORT F. write JTD bit twice within four cycles.
MCUCR |= (1<<JTD);
MCUCR |= (1<<JTD);
};
void led_init_ports() {
// * Set our LED pins as output
DDRB |= (1<<4);
}
void led_set_kb(uint8_t usb_led) {
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
// Turn capslock on
PORTB |= (1<<4);
} else {
// Turn capslock off
PORTB &= ~(1<<4);
}
}
/* Clueboard 2.0 LED locations:
*
* Capslock: B4, pull high to turn on
* LCtrl: Shared with Capslock, DO NOT INSTALL LED'S IN BOTH
* Page Up: B7, pull high to turn on
* Escape: D6, pull high to turn on
* Arrows: D4, pull high to turn on
*/
void backlight_init_ports(void) {
print("init_backlight_pin()\n");
// Set our LED pins as output
DDRD |= (1<<6); // Esc
DDRB |= (1<<7); // Page Up
DDRD |= (1<<4); // Arrows
// Set our LED pins low
PORTD &= ~(1<<6); // Esc
PORTB &= ~(1<<7); // Page Up
PORTD &= ~(1<<4); // Arrows
}
void backlight_set(uint8_t level) {
if ( level == 0 ) {
// Turn off light
PORTD |= (1<<6); // Esc
PORTB |= (1<<7); // Page Up
PORTD |= (1<<4); // Arrows
} else {
// Turn on light
PORTD &= ~(1<<6); // Esc
PORTB &= ~(1<<7); // Page Up
PORTD &= ~(1<<4); // Arrows
}
}