Cleanup rules.mk for 32U4 keyboards, 0-9 (#6789)

master
fauxpark 2019-09-24 17:59:17 +10:00 committed by noroadsleft
parent 37b6a2abbd
commit 237147ca23
29 changed files with 118 additions and 1183 deletions

View File

@ -1,51 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable

View File

@ -1,6 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = atmel-dfu BOOTLOADER = atmel-dfu
# Build Options # Build Options

View File

@ -1,45 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = atmel-dfu
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.

View File

@ -1,62 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
#EXTRAFLAGS += -flto
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,45 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = caterina
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.

View File

@ -1,24 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
F_CPU = 16000000 # Teensy halfkay
# Pro Micro caterina
# # Atmel DFU atmel-dfu
# LUFA specific # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# Target architecture (see library "Board Types" documentation). # ATmega32A bootloadHID
ARCH = AVR8 # ATmega328P USBasp
# Input clock frequency.
F_USB = $(F_CPU)
# Bootloader
BOOTLOADER = caterina BOOTLOADER = caterina
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #

View File

@ -1,45 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader
# This definition is optional, and if your keyboard supports multiple bootloaders of
# different sizes, comment this out, and the correct address will be loaded
# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina BOOTLOADER = caterina
# Build Options # Build Options

View File

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,61 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,62 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,62 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #

View File

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,58 +1,12 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096

View File

@ -1,58 +1,12 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = halfkay BOOTLOADER = halfkay
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096

View File

@ -1,62 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #

View File

@ -1,64 +1,6 @@
# Overrides for Feather 32u4 Bluefruit # Processor frequency
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 8000000 F_CPU = 8000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# atmega32a bootloadHID
BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,62 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,62 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically # the appropriate keymap folder that will get included automatically

View File

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,62 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# comment out to disable the options. # comment out to disable the options.
# #

View File

@ -1,63 +1,16 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change yes to no to disable # change yes to no to disable
# #

View File

@ -1,5 +1,15 @@
MCU = atmega32u4 # MCU name
BOOTLOADER = caterina MCU = atmega32u4
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina
EXTRAKEY_ENABLE = yes EXTRAKEY_ENABLE = yes
NKRO_ENABLE = yes NKRO_ENABLE = yes

View File

@ -1,49 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = caterina
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in

View File

@ -1,48 +1,14 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader selection # Bootloader selection
# Teensy halfkay # Teensy halfkay
# Pro Micro caterina # Pro Micro caterina
# Atmel DFU atmel-dfu # Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu # LUFA DFU lufa-dfu
# QMK DFU qmk-dfu # QMK DFU qmk-dfu
# atmega32a bootloadHID # ATmega32A bootloadHID
# ATmega328P USBasp
BOOTLOADER = caterina BOOTLOADER = caterina
# Build Options # Build Options

View File

@ -1,49 +1,15 @@
# MCU name # MCU name
MCU = atmega32u4 MCU = atmega32u4
# Processor frequency. # Bootloader selection
# This will define a symbol, F_CPU, in all source code files equal to the # Teensy halfkay
# processor frequency in Hz. You can then use this symbol in your source code to # Pro Micro caterina
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done # Atmel DFU atmel-dfu
# automatically to create a 32-bit value in your source code. # LUFA DFU lufa-dfu
# # QMK DFU qmk-dfu
# This will be an integer division of F_USB below, as it is sourced by # ATmega32A bootloadHID
# F_USB after it has run through any CPU prescalers. Note that this value # ATmega328P USBasp
# does not *change* the processor frequency - it should merely be updated to BOOTLOADER = caterina
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options # Build Options
# change to "no" to disable the options, or define them in the Makefile in # change to "no" to disable the options, or define them in the Makefile in