qmk-dactyl-manuform-a/keyboard/gh60/Makefile

135 lines
4.4 KiB
Makefile
Raw Normal View History

2012-12-26 18:41:32 +01:00
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
# Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# Target file name (without extension).
TARGET = gh60_lufa
# Directory common source filess exist
2015-04-09 18:53:24 +02:00
TMK_DIR = ../../tmk_core
2012-12-26 18:41:32 +01:00
# Directory keyboard dependent files exist
TARGET_DIR = .
2013-03-11 07:28:14 +01:00
# project specific files
2013-11-21 08:32:45 +01:00
SRC = keymap_common.c \
2012-12-26 18:41:32 +01:00
matrix.c \
led.c
2013-11-25 01:27:25 +01:00
2013-11-21 08:32:45 +01:00
ifdef KEYMAP
SRC := keymap_$(KEYMAP).c $(SRC)
else
2015-10-27 17:47:12 +01:00
SRC := keymap_poker.c $(SRC)
2013-11-21 08:32:45 +01:00
endif
2012-12-26 18:41:32 +01:00
CONFIG_H = config.h
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
2013-03-09 14:23:32 +01:00
# Interrupt driven control endpoint task(+60)
2013-11-21 08:32:45 +01:00
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
2013-03-09 14:23:32 +01:00
2012-12-26 18:41:32 +01:00
2013-03-29 03:31:21 +01:00
# Boot Section Size in *bytes*
2013-03-27 07:21:16 +01:00
# Teensy halfKay 512
2013-03-29 03:31:21 +01:00
# Teensy++ halfKay 1024
2013-03-27 07:21:16 +01:00
# Atmel DFU loader 4096
# LUFA bootloader 4096
2013-03-29 03:31:21 +01:00
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
2013-03-27 07:21:16 +01:00
2012-12-26 18:41:32 +01:00
# Build Options
# comment out to disable the options.
#
2013-03-11 07:28:14 +01:00
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
2013-03-09 14:23:32 +01:00
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
2013-11-21 11:32:17 +01:00
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
2013-11-21 08:32:45 +01:00
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
2012-12-26 18:41:32 +01:00
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
2012-12-26 18:41:32 +01:00
# Search Path
VPATH += $(TARGET_DIR)
2015-04-09 09:20:42 +02:00
VPATH += $(TMK_DIR)
2012-12-26 18:41:32 +01:00
2015-04-09 09:20:42 +02:00
include $(TMK_DIR)/protocol/lufa.mk
include $(TMK_DIR)/common.mk
2015-10-27 17:47:12 +01:00
include $(TMK_DIR)/rules.mk