qmk-dactyl-manuform-a/keyboards/massdrop/ctrl/config.h

/*
Copyright 2015 Jun Wako <wakojun@gmail.com>

This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.

This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with this program.  If not, see <http://www.gnu.org/licenses/>.
*/

#pragma once

#include "config_common.h"

/* USB Device descriptor parameter */
#define VENDOR_ID           0x04D8
#define PRODUCT_ID          0xEED2
#define DEVICE_VER          0x0101

#define MANUFACTURER        "Massdrop Inc."
#define PRODUCT             "CTRL Keyboard"
#define SERIAL_NUM          "Unavailable"

/* key matrix size */
#define MATRIX_ROWS 11
#define MATRIX_COLS 8

#define MATRIX_ROW_PINS { B04, B05, B06, B07, B08, B09, A10, A11, B10, B11, B12 }
#define MATRIX_COL_PINS { A00, A01, A02, A03, A04, A05, A06, A07 }
#define UNUSED_PINS

/* COL2ROW, ROW2COL */
#define DIODE_DIRECTION COL2ROW

/* Temporary solution for matrix delay */
#define IGNORE_ATOMIC_BLOCK

/* Avoid out-of-bounds errors when SmartEEPROM is not enabled */
#define EEPROM_SIZE 1024

/* MCU Port name definitions */
#define PA 0
#define PB 1

/* This Shift Register expands available hardware output lines to control additional peripherals */
/* It uses four lines from the MCU to provide 16 output lines */
/* Shift Register Clock configuration (MCU to ShiftRegister.RCLK) */
#define SR_EXP_RCLK_PIN          B14
/* Shift Register Output Enable configuration (MCU to ShiftRegister.OE_N) */
#define SR_EXP_OE_PIN            B15
/* SERCOM port to use for Shift Register SPI */
/* DATAOUT and SCLK must be configured to use hardware pins of this port */
#define SPI_SERCOM               SERCOM2
/* Shift Register SPI Data Out configuration (MCU.SERCOMx.PAD[0] to ShiftRegister.SER) */
#define SPI_DATAOUT_PIN          A12
#define SPI_DATAOUT_MUX          2
/* Shift Register SPI Serial Clock configuration (MCU.SERCOMx.PAD[1] to ShiftRegister.SRCLK) */
#define SPI_SCLK_PIN             A13
#define SPI_SCLK_MUX             2

/* Debug LED (Small LED Located near MCU) */
#define DEBUG_LED_ENABLE            1
#define DEBUG_LED_PORT              PA
#define DEBUG_LED_PIN               27

/* Additional debugging ports */
/* PCB M21 */
#define DEBUG_PORT1_ENABLE          1
#define DEBUG_PORT1_PORT            PB
#define DEBUG_PORT1_PIN             3
/* PCB M23 */
#define DEBUG_PORT2_ENABLE          1
#define DEBUG_PORT2_PORT            PB
#define DEBUG_PORT2_PIN             17
/* PCB M25 */
#define DEBUG_PORT3_ENABLE          1
#define DEBUG_PORT3_PORT            PA
#define DEBUG_PORT3_PIN             20

/* Debug Boot Tracing - During boot sequence, ground this pin to halt and display debug code using Debug LED */
/* This is useful in determining which hardware device may have malfunctioned or is improperly configured */
/* Feature is automatically disabled after successful boot */
/* PCB M27 */
#define DEBUG_BOOT_TRACING_ENABLE   1
#define DEBUG_BOOT_TRACING_PORT     PB
#define DEBUG_BOOT_TRACING_PIN      23

/* USB2422 config */
#define USB2422_ADDRESS 0x58
#define USB2422_VENDOR_ID 0x04D8
#define USB2422_PRODUCT_ID 0xEEC5
#define USB2422_DEVICE_VER 0x0101
#define USB2422_MANUFACTURER "Massdrop Inc."
#define USB2422_PRODUCT "Massdrop Hub"
#define USB2422_ACTIVE_PIN A18

/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCE 5

/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
//#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
//#define LOCKING_RESYNC_ENABLE

/* Force boot in NKRO mode */
//#define FORCE_NKRO

/*
 * Feature disable options
 *  These options are also useful to firmware size reduction.
 */

/* disable debug print */
//#define NO_DEBUG

/* disable print */
//#define NO_PRINT

/* disable action features */
//#define NO_ACTION_LAYER
//#define NO_ACTION_TAPPING
//#define NO_ACTION_ONESHOT
//#define NO_ACTION_MACRO
//#define NO_ACTION_FUNCTION

#define RGB_MATRIX_KEYPRESSES
#define RGB_MATRIX_LED_PROCESS_LIMIT 15
#define RGB_MATRIX_LED_FLUSH_LIMIT 10

#include "config_led.h"