qmk-dactyl-manuform-a/converter/sun_usb/README

100 lines
2.5 KiB
Plaintext
Raw Normal View History

2012-10-18 03:41:37 +02:00
Sun to USB keyboard protocol converter
======================================
2012-10-19 07:06:18 +02:00
Target MCU is ATMega32u4 but other USB capable AVR will also work.
Supported keyboards: Sun Type 5 Keyboard, CTCSP SHORT TYPE KEYBOARD(CKUB)
CTCSP SHORT TYPE KEYBOARD: http://imgur.com/a/QIv6p
2012-10-18 03:41:37 +02:00
Connector
2012-10-19 07:06:18 +02:00
---------
2012-10-18 03:41:37 +02:00
8Pin mini DIN
___ ___
/ |_| \
/ 8 7 6 \
| 5 4 3 |
\_ 2 1 _/
\_____/
(receptacle)
2012-10-19 07:06:18 +02:00
Wiring:
Pin mini DIN MCU
----------------------------------
1 GND GND
2 GND GND
3 5V
4 RX/TX(Mouse)
5 RX PD3
6 TX PD2
7 GND GND
8 5V VCC
2012-10-18 03:41:37 +02:00
2012-10-19 07:06:18 +02:00
Protocol
2012-10-18 03:41:37 +02:00
--------
2014-01-05 04:45:52 +01:00
Signal: Asynchronous, Negative logic, 1200baud, No Flow control
2012-10-19 07:06:18 +02:00
Frame format: 1-Start bit, 8-Data bits, No-Parity, 1-Stop bit
AVR USART engine expects positive logic while Sun keyboard signal is negative.
2014-01-05 04:45:52 +01:00
To use AVR UART engine you need external inverter in front of RX and TX pin.
2012-10-19 07:06:18 +02:00
Otherwise you can software serial routine to communicate the keyboard.
This converter uses software method, you doesn't need any inverter part.
Commands From System To Keyboard
0x01 Reset
Keyboard responds with following byte sequence:
Success: 0xFF 0x04 0x7F
Fail: 0x7E 0x01 0x7F
0x02 Bell On
0x03 Bell Off
0x0A Click On
0x0B Click Off
0x0E LED
followed by LED status byte:
bit: 3 2 1 0
LED: CapsLk ScrLk Compose NumLk
0x0F Layout
Keyboard responds with 'Layout Response' 0xFE 0xXX
Commands From Keyboard To System
0x7F Idle
means no keys pressed.
0xFE Layout Response
0xFF Reset Response(followed by 0x04)
Reference
http://kentie.net/article/sunkbd/page2.htm
http://kentie.net/article/sunkbd/KBD.pdf
Build Firmware
--------------
Just use 'make'
2012-10-18 03:41:37 +02:00
$ cd sun_usb
$ make
2012-10-19 07:06:18 +02:00
Then, load the binary to MCU with your favorite programmer.
Sun commands
------------
You can send Sun protocol commands with TMK `Magic` key combo. By default `Magic` key is `LShift` + `RShift`, `LAlt` + `RAlt' or `LMeta` + `RMeta`.
https://github.com/tmk/tmk_keyboard#magic-commands
Following Sun specific commands are available. For example, to send 'Bell On' you can press `LShift` + `RShift` + `Up` keys simultaneously.
```
----- Sun converter Help -----
Up: Bell On
Down: Bell Off
Left: Click On
Right: Click Off
PgUp: LED all On
PgDown: LED all On
Insert: Layout
Delete: Reset
```