qmk-dactyl-manuform-a/keyboard/hhkb/Makefile

150 lines
5.0 KiB
Makefile
Raw Normal View History

#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
# Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# Target file name (without extension).
TARGET = hhkb_qmk
# Directory common source filess exist
TOP_DIR = ../..
2015-04-09 18:53:24 +02:00
TMK_DIR = ../../tmk_core
# Directory keyboard dependent files exist
TARGET_DIR = .
# # project specific files
SRC = hhkb_qmk.c \
matrix.c
ifdef KEYMAP
SRC := keymaps/keymaps/$(KEYMAP).c $(SRC)
else
SRC := keymaps/keymaps/default.c $(SRC)
endif
CONFIG_H = config.h
# MCU name
#MCU = at90usb1287
2013-07-28 10:34:41 +02:00
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
#OPT_DEFS += -DBOOTLOADER_SIZE=4096
# as per original hasu settings
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
CUSTOM_MATRIX = yes # Custom matrix file for the HHKB
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
# NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
# MIDI_ENABLE = YES # MIDI controls
# UNICODE_ENABLE = YES # Unicode
# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
2015-01-10 17:54:17 +01:00
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
2015-01-10 17:54:17 +01:00
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
2015-04-09 09:20:42 +02:00
VPATH += $(TMK_DIR)
2013-10-07 16:28:17 +02:00
debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
2012-12-15 18:32:07 +01:00
debug-on: all
2013-10-07 16:28:17 +02:00
debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
2013-10-07 16:28:17 +02:00
debug-off: all
include $(TOP_DIR)/quantum/quantum.mk