qmk-dactyl-manuform-a/converter/terminal_bluefruit/Makefile

114 lines
3.4 KiB
Makefile
Raw Normal View History

# Target file name (without extension).
TARGET = terminal_bluefruit
# Directory common source filess exist
TOP_DIR = ../..
# Directory keyboard dependent files exist
TARGET_DIR = .
# keyboard dependent files
SRC = keymap.c \
matrix.c \
led.c
CONFIG_H = config.h
BLUEFRUIT_TRACE_SERIAL=true
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
#MCU = at90usb162 # Teensy 1.0
MCU = atmega32u4 # Teensy 2.0
#MCU = at90usb646 # Teensy++ 1.0
#MCU = at90usb1286 # Teensy++ 2.0
# Processor frequency.
# Normally the first thing your program should do is set the clock prescaler,
# so your program will run at the correct speed. You should also set this
# variable to same clock speed. The _delay_ms() macro uses this, and many
# examples use this variable to calculate timings. Do not add a "UL" here.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in bytes
# Teensy halfKay 512
# Atmel DFU loader 4096
# LUFA bootloader 4096
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
#
# PS/2 protocol implementations
# USART is recommended if it is available, others are for reference purpose.
# INT implementation will drop simultaneous key strokes.
#
#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
#PS2_USE_BUSYWAIT = yes # uses primitive reference code
ifdef PS2_USE_USART
SRC += protocol/ps2_usart.c
OPT_DEFS += -DPS2_USE_USART
endif
ifdef PS2_USE_INT
SRC += protocol/ps2.c
OPT_DEFS += -DPS2_USE_INT
endif
ifdef PS2_USE_BUSYWAIT
SRC += protocol/ps2.c
OPT_DEFS += -DPS2_USE_BUSYWAIT
endif
#---------------- Programming Options --------------------------
PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
include $(TOP_DIR)/protocol/bluefruit.mk
include $(TOP_DIR)/protocol.mk
include $(TOP_DIR)/common.mk
include $(TOP_DIR)/rules.mk